Gas Dryer Not Heating

Make sure the gas to your dryer is turned on.

• On the gas supply pipe to your dryer, there will be a small valve that controls the gas.
• Make sure the handle lines up with the pipe (on), and is not turned so it is 90 degrees to the pipe (off).

Your gas dryer relies on a multi-step chain of events to ignite the gas and also to make sure that the gas doesn't get out when it shouldn't and ignite a fire in your home. To do this, the gas valve on your machine is really two valves in one. One valve will only allow gas to flow to the second valve if the machine is turned on and has power and the controls are set to require heat. The second valve will only allow gas to flow to the burner if the conditions are proper for the gas to be ignited.

• Your gas is usually lit by an igniter, a device that glows brightly when energized and gets hot enough to ignite the gas.
• A device called a flame or radiant sensor monitors this igniter and causes the gas to flow when the igniter is hot enough. It will allow the gas to continue to flow as long as the gas is burning properly.
• The solenoid coils on the gas valve can wear out over time so that they won't open the gas valve when they should.

You can check to see if this process is happening by watching the gas burner through a small observation port in the front panel of your dryer. Just pry off the small cover with a screwdriver. Some dryers won't have this port, but if you remove the top of the unit you can still see. Others will have a kick panel that can be removed. Be careful if you have to remove some of the cabinet (case) because of moving parts and possible shock hazards.

• Set the dryer to a setting that will require heat and start it.
• Make sure the setting you use requires heat and is not a cool-down time, which can be the last part of some cycles.
• It is best to test on a high heat setting and use a timed cycle.
• Watch the gas burner and see if the igniter glows.
• If there is no glow at all, you will need to check the igniter itself, along with the thermal fuse (see below).
  • Unplug the dryer and open the cabinet.
  • The Igniter should show about 80-400 ohms.
  • if it is showing more resistance or no continuity at all it's bad; replace it.
  • You can check the thermal fuse for simple continuity. If none, replace it.
• If the igniter glows and stays on for a long time (five minutes), and no flame starts, the problem is the flame (or radiant) sensor.
• If the igniter glows and stays on for a shorter time (up to two minutes) and then goes out with no flame igniting, the problem is the gas valve coils. Unplug the dryer, and test them for proper resistance (500-1500 ohms). Replace them if they show no continuity. Here's a good video to help you check them.

Because the thermal fuse is a relatively frequent culprit, we start with this check. It can be a sign of other problems, so follow all the checks and don't just stop with replacing the thermal fuse if it is blown.

• Make sure the thermal fuse (TF) isn't blown. Check it for continuity.
• If it shows continuity, go on to Thermal Cutoff Blown, below.
• If there's none, it has blown. Replace it.
• If it has blown, the dryer may still spin, but won't heat. In other circumstances the dryer won't run at all. Replace the thermal fuse and....
  1. If TF is blown, make sure to check that your exhaust ducts are not clogged with lint.
  2. If TF is blown, also check your blower wheel as well for lint buildup or stray clothing, like a sock, which will impede airflow and cause this sort of overheating.
  3. More details on properly checking dryer airflow and ducts can be found on our Dryer Maintenance page
  4. If the TF is blown, check the Thermal Cutoff (below) as well.
  5. If the TF is blown, it is a good idea to just replace the Hi-Limit thermostat as well, since intermittent failures in the Hi-Limit can cause blown thermal fuses.

The thermal cutoff, if blown or tripped can also cause the dryer to not heat.

• Occasionally these will have a reset button on them, but most of the time they are like the TF a one-shot device.
• It will be located near the heat source. Test for continuity, if it checks, it's good. If no continuity, replace it, and like the thermal fuse, check for other problems with airflow.

If the ducts are clear, it's a good idea to replace the Hi-Limit thermostat.

• When the Hi-Limit fails and sticks on because of a problem, the thermal fuse will blow (it's very reliable).
• Since this Hi-Limit issue could be intermittent, and the part is relatively inexpensive, replace it along with the thermal fuse.
• Check it for continuity, if it has none, replace it.
• If the Thermal Fuse or Thermal Cutoff was blown replace the Hi-Limit as well.

The cycling thermostat can stick open, causing the dryer to think it is hot enough, and not supply heat. Disconnect it from the wiring in the dryer and test for continuity (at room temperature). If no continuity, replace it.

A less common failure is the centrifugal switch on the motor.

• This switch closes to maintain contact between the motor and power source, and also completes the circuit for the gas control system.
• Failure of this switch will keep power from the gas valve, which will ultimately prevent heat from reaching your clothes.
• The switch contacts can be replaced independently.
• Test the switch for continuity.
  • You will need to determine which contacts are allowing current to flow through the gas valve.
  • Disconnect one terminal and then check the switch for continuity. if none, the switch needs to be replaced (or possibly cleaned, but replacing is more sure) Here's a good video that shows how.
• If the switch operating mechanism on the motor shaft has gone bad, you will have to replace the entire motor. In this case, the dryer motor probably won't be running right either.

Another less common failure is the timer assembly; the contacts which control the heat source may have failed. If your timer assembly has failed, you'll have to replace it, but timers can be expensive and are commonly misdiagnosed. Use a multimeter to check for voltage at the heating circuit and motor circuit before replacing the timer assembly.

When all else fails, you should check the Gas Valve relay on the control board if you can locate it and if it is replaceable. You can trace the wiring from the gas valve back to the control board and note if it is connected to a device on the control board that is usually a small rectangular component. the terminals are frequently on the device itself. Check to see if the device can be removed from the control board. If so you can try changing it out.

If that isn't possible or doesn't fix things, you can replace the control board.