Phillips #000 Screwdriver

$5.95

Product code: IF145-030-3

Click Image To Zoom

 
 
 
 

Phillips #000 Screwdriver

$5.95

Product code: IF145-030-3

Product Overview

A very small screwdriver, for very small screws

  • Don't be fooled! Many screwdrivers are incorrectly marked as #000, but are too large to unscrew the teensie and delicate #000 screws.
  • High quality steel shaft and hand-tested tip ensure a quality drive, every time.

This size bit is also available as an exchangeable bit in our popular 54 Bit Driver Kit , carefully designed to include the most common and often hard to find driver bits used in electronics repair. This driver is also a part of the Pro Tech Screwdriver Set.

Product Details

  $5.95 iFixit

 

Condition:

New

Available: 50+

Add to Cart
 

Stories

My Problem

Both phones (iPhone 5 and Moto X) had batteries older than 2 years and required frequent charging.

My Fix

Both phones were relatively easy to repair. Your guides and uTube videos were very helpful. Also other uTube videos not from ifixit were informative as well. Be very careful to check the iPhone power switch cable connector, took me 2 additional disassemblies before I got it right. Both repairs went great, saved a ton of money and did not have to switch phones.

My Advice

Take your time and don't force anything. Make sure you are getting a new battery. People are selling used batteries on eBay and Amazon.

My Problem

bought tools and screen

My Fix

tricky but I managed.

My Advice

No. It is all very well explained. I must be done with calm and concentration. Thankyou

My Problem

I was working at Starbucks when my friend Carlos saw me and came over to give me a hug. I knocked a whole bottle of Soylent on my keyboard. Eek.

My Fix

It took about two hours total. I was going extra slowly because I had not worked on a Macbook before. If I should need to do it again, god forbid, it could be an hour or less.

My Advice

The difficulty level is listed as moderate, but I would say it is low if you have built computers in the past. Memories of untangling SATA cables in mini towers and puzzling over new circuit boards that are DOA (Plush carpeting? I admit nothing!) made this feel easy in comparison. I made a point to buy the anti-static wrist strap anyway. Even though my current place has hardwood floors.

There is little agreement on the Internet about the correct method of grounding anti-static wrist straps. This is what I did. Imitate at your own risk:

Macbook adapter is not grounded. So I plugged it into a grounded power strip and plugged that into the wall. I turned the power strip off. Plugged the adapter into the laptop. Clipped the wrist strap to whatever metal laptop component presented itself (not an easy task--had to reposition multiple times).

Everyone made it through ok. Happily using new keyboard.

My Problem

Because my BEAUTIFUL daughter is a clutz!

My Fix

Just like it should, thanks to your how to video!!

My Advice

Be patient and have a work space away from distraction and animals, allow plenty of time for the first one, LOL! the second one goes smoother!

shaneeudy's Story Photo #617131
shaneeudy's Story Photo #617130

My Problem

Lightning connector developed a short which made charging difficult.

My Fix

Everything went very smoothly until the last step. The guide was perfect, detailing everything you needed to know. Unfortunately, there should have been one final step. There are 3 components that need to be reused from your old Lightning connector assembly. The guide doesn't mention anything about this at all. I was able to figure it out pretty easily because I work on cars for a living - many times without repair information - but I suspect this oversight may trip up quite a few people. I tried to submit an edit but it was rejected. Perhaps I didn't format it right or something. In any case I still think iFixit needs to update this guide, but if they don't I've attached two photos showing the 3 components. Other than that, it was a fairly uneventful repair (expect when I broke a battery adhesive strip).

My Advice

DON'T BREAK THE BATTERY ADHESIVE STRIPS!!! Seriously, take your time and follow the guide EXACTLY! I got the first strip out perfectly in one piece. The second broke almost immediately. I later realized it was because I pulled it at a 45 degree angle, which was perfect for the first one, but the second was supposed to be pulled straight up. Doh! If you do break it, heat the CRAP out of it with a hairdryer (min. 5 minutes with 1800w unit on high) and use the guitar string trick. Forget the dental floss, I don't know why they even mention it. Breaking the 2nd adhesive strip added well over an hour to the job. Don't do it. Take your time and you'll have a much nicer time!

My Problem

Ordered from iFixit a battery because it was not that good but that was not enough so I ordered a iPhone 4S Dock Connector and replaced the and that worked.

The phone is now perfect

My Fix

Everything was very easy with all that excellent repair guides

My Advice

Follow the Repair Guides

My Problem

The two-year old iPhone 5 lost battery capacity and got hot during charging. In addition, its screen began to bulge outwards and got psychedelic background colors. From iFixit stories, we understood that the battery was due for replacement.

My Fix

Following the procedure given by iFixit, the fix was straightforward. All described problems were encountered but overcome. But one comment: The procedure mentioned that the battery was glued to the phone and some careful prying would be required. But you would not imagine how intensely hard our old battery stuck to the phone - most probably due to the glue being dried out from heat during charging. However, with a combination of good prying tools, strong finger muscles, thoughtful carefulness and quite a lot of patience - we struggled with this battery glue for almost an hour before the battery eventually came out - the fix was a success!

My Advice

Be careful and take your time with the old battery. Drag plastic tab, and pry where shown in iFixit procedure, and the battery glue will be defeated, gradually, slowly...!

My Problem

Broken Screen and a pretty faulty front facing camera! Be cautions when taking off a phone case to enjoy that new screen you just replaced... the bare phone is just a *little* less grippy, and you might find yourself back where you started!

My Fix

Pretty alright! A couple of issues, and unfortunately the new screen got cracked in a couple of places, but from what I hear that's almost a given the first time around. Took me about one relatively frustrating hour, mostly dealing with re-shaping the case from bends from impact damage.

My Advice

A few things!

1) never force it. If the screen isn't settling in, IT WONT FIT. There's some pressure needed, but be a good judge. Glass is not flexible.

2) Check the rim for bends and damage. Often when the screen is cracked, the impact was enough to bend the metal rim around it. If it's not almost perfectly shaped, that glass will not fit!

3) when using the opening tools, gently slide the tip up each side - don't jam it in there like a pry bar, you just want a bit of gently wedge pressure moving up to dislodge the screen.

4) Don't be surprised (or discouraged!) if your first screen (or two) breaks. Repairing electronics is an art and takes practice. It might be expensive now, but after you learn a few times, It'll be easy and you'll really start saving money! (and impressing your friends)

5) work on a nice, flat table. avoid edges where you can drop and lose those teensy teensy screws (oops)

6) keep the leftovers! If anything can be salvaged, don't toss it. When you upgrade, keep the old tech around to practice repairs on. As stated before, practice makes perfect! and perfect makes money :)

My Problem

Someone I knew had a home button that was falling out.

My Fix

Fine super easy took about 15 minutes.

My Advice

Take your time I only did it quick because I use to be an Apple Genius.

My Problem

battery old

My Fix

didn't take long. The pictures didn't show the battery connector actually disconnected, so I got it mixed up with the little shielded connector up and to the left.

There was also a little part not in the picture, on the same place as the top left screw, a grounding tab to the back case.

My Advice

The battery connector is the big one, not the little one on the top left that it looks like they are prying off in the picture with the plastic tool.