Introduction

Suffering from a rapidly waning, or non-existant, battery life? Use this guide to replace the battery in your Motorola Moto X.

Video Overview

Image 1/3: Remove the SIM card tray.
  • Insert the SIM card eject tool into the hole in the side of the SIM card tray and push to eject the tray.

  • Remove the SIM card tray.

  • If the SIM card does not fall free from the tray on its own, simply remove it with your fingers.

Add Comment

Image 1/3: Insert a plastic opening tool into the seam between the front and rear covers near the SIM card slot.
  • In the following steps you will be releasing the clips holding the phone's cases together. However, the back case is also secured with an adhesive pad. After separating the clips you will use an iOpener to allow the case to fully open. Do not attempt to fully open the phone before loosening the adhesive.

  • Insert a plastic opening tool into the seam between the front and rear covers near the SIM card slot.

  • Slide the plastic opening tool along the seam toward the upper corner.

Add Comment

Image 1/2:
  • Carefully slide the plastic opening tool around the corner, freeing it from clips.

Add Comment

Image 1/2:
  • Run the plastic opening tool along the seam nearest the headphone jack on the top of the phone.

Add Comment

Image 1/2:
  • Pry around the top right corner of the phone between the two covers.

Add Comment

Image 1/2: The plastic on the front cover is thinner here and the buttons may move around; go slowly to avoid damaging the buttons or the front cover.
  • Carefully slide the opening tool along the button side of the phone.

  • The plastic on the front cover is thinner here and the buttons may move around; go slowly to avoid damaging the buttons or the front cover.

Be *very* careful not to push the opening tool too deep when you go around the buttons! I accidentally broke the volume rocker ribbon by doing so, and didn't even realize it until I had completely removed the cover.

Simeon Simeonides - Reply

When i removed the volume rocker i cant get it back in correctly seems to be in right but the volume up is not clicking and only works if i push it really hard any ideas?

Alf stevens - Reply

Image 1/2:
  • Insert a plastic opening tool into the seam just below the volume rocker to widen the gap.

Add Comment

Image 1/2:
  • Continue prying to the lower corner of the phone.

Add Comment

Image 1/2:
  • Carefully pry from the corner to the edge of the USB port.

Add Comment

Image 1/2:
  • Insert the plastic opening tool at the other end of the USB port and slide around the corner.

Add Comment

Image 1/2: Once you are certain the clips have all been separated, use the following two steps to prepare your iOpener.
  • Continue separating clips around the corner and along the length of the phone.

  • Once you are certain the clips have all been separated, use the following two steps to prepare your iOpener.

Add Comment

Image 1/2: Place the iOpener in the center of the microwave.
  • We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

  • Place the iOpener in the center of the microwave.

    • For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

Add Comment

Image 1/1: Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.
  • Heat the iOpener for thirty seconds.

  • Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.

  • Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.

  • Never touch the iOpener if it appears swollen.

  • Always wait at least three minutes before reheating the iOpener.

Add Comment

Image 1/1: The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.
  • Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

  • The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

Add Comment

Image 1/1:
  • Lay the iOpener over the phone to loosen the adhesive securing the back cover. Let the bag sit on the device for approximately 90 seconds before attempting to remove the cover.

There is NO GLUE holding on the back of a Moto X with a wood back! That little fact just made the extra $50 I spent on the phone totally worthwhile.

Doug Larrick - Reply

Lucky for you, I have the bamboo, and plenty of adhesive.

Kelly F -

Image 1/3: The back cover is very flexible, but you don't want to damage any internal components by being too hasty.
  • Starting from the SIM slot side, carefully peel the back cover off of the phone.

  • The back cover is very flexible, but you don't want to damage any internal components by being too hasty.

  • Do not separate the back cover entirely; it is still connected to the phone by the camera flash cable.

    • The flash cable is attached on the power/volume button side of the phone.

Step 15 seemed to be the hardest part for me. (step 25, the battery was also difficult). I am now not a fan of sticky stuff, "Mild adhesive" is definitely an understatement, IMHO, just saying I don't like sticky stuff, maybe I didn't do it right. The iOpener seemed to help a little, but not much.

***CAUTION***

BE CAREFUL with the NFC antenna, it says "X8 Mobile Computing System" on it. The adhesive seemed stick to the the blue stuff on the back cover more and loosen up on the bottom of the antenna, the part that sticks to the battery. So in the process of peeling the back cover the antenna started to come up and was torn at the connector strip before I realized what was happening, step 19 has a good picture of the connector strip that I'm talking about. I like using NFC once in awhile, so now my next FIX will be the antenna.

Overall instructions were GREAT, I now have a camera again. Thank you.

Patrick - Reply

So you are saying that there is no problem if I don't connect the NFC antenna? I'm asking this because I bought a replacement battery that don't include the NFC antenna. I would really appreciate your help with this :)

jspsaucedo -

The adhesive was crazy hard on mine as well and I ended up with two small cracks on the edges of my back cover. The blue rubber piece actually separated from the back and removed it from the battery after it was open. The battery itself was also very difficult to remove (pull tab did nothing) and bent/pried the old battery out. I see no reason for all that adhesive! Other than getting the dang thing open the rest was easy. Great guide!

Darrell Jividen - Reply

The adhesive holding the back very strong! In the process of removing the back, I cracked the edges of the back cover and ripped part of the NFC connector. Luckily the friend I was doing the repair for did not even know what NFC was, so she was ok with this. Take your time removing the back cover! Also, the adhesive holding the battery in place was not what I would call mild. The black tab was next to useless in removing the battery

Danny Smandych - Reply

So you are saying that there is no problem if I don't connect the NFC antenna? I'm asking this because I bought a replacement battery that don't include the NFC antenna.

jspsaucedo -

Thank you for the guide !!! comments were really useful too. Read them.

fabajaja - Reply

Image 1/1:
  • Gently set the back cover down in a way that exposes the camera flash cable connector, but does not put strain on it.

As I had seen in another video, my Moto X with a custom back did not have the blue sticky pad. But the back was still well-adhered in the top corners and with a strip of adhesive along the bottom. In the photo in this step you can see the only adhesive I had to deal with, which was on either side of the lens (two dark areas on the phone back) and along the bottom of the phone (dark area at the bottom of the phone back).

pdisc1 - Reply

Image 1/3: Be sure to pry only on the flap itself, '''not''' on the connector.
  • Use the tip of a spudger to flip up the retaining flap on the flash cable ZIF connector.

  • Be sure to pry only on the flap itself, not on the connector.

  • Pull the flash cable straight out of its socket.

Add Comment

Image 1/1:
  • Separate the back cover from the phone.

Add Comment

Image 1/1: Remove the four 3 mm T3 Torx screws securing the lower antenna assembly to the phone.
  • Remove the four 3 mm T3 Torx screws securing the lower antenna assembly to the phone.

  • Remove the four 3 mm T3 Torx screws securing the lower antenna assembly to the phone.

It turns out to be the hardest step at the moment. I ordered iOpener set, and it is almost useless. It doesn't have t3, only t5, the actual iOpener is useless. I would happily order t3 on ifixit.com, but there is no t3 in Germany, so I ordered on amazon, and it turned out to be a complete $@$*, I was not able to take a single screw out. The guide is really good, I never thought I would have an issue with a screwdriver ....

Igor Gaidaichuk - Reply

These screws were definitely incompatible with my T3 bit - it was too small. T4 worked fine. Not sure if I should attribute this to an error in the guide or inconsistency in the size of my bit set; in any case it might be handy to have a T4 handy if you're not buying the iFixit screwdriver.

Christian Hinton - Reply

Stripped two of four T3 screws almost instantly and with very little force. Be careful! If I can't carve a flat slot into the screw heads I guess I'll have to abort the project or deliberately crack the antenna assembly plastic or try to drill the screw heads to proceed.

pdisc1 - Reply

Drilled out the heads. A bit scary, yes. I agree with another commenter here that my T3 isn't the best fit in these screws. My T3 was a pretty cheap eBay acquisition, so who knows where the blame should go. I wouldn't do this repair again. Phones should be easier to break open than this one. Too much adhesive (and as I mentioned above, mine didn't even have the blue adhesive pad) and T3 heads are super small and asking to be stripped and the two screws I did get out were way too tight. Oh, and also the potential butchering of the cover when prying loose the clips. Mine bent a bit around the headphone jack, but it smoothed back down and is not noticeable. Phone powered up and is charging now. Let's hope it was worth it.

pdisc1 - Reply

Image 1/3: Remove the antenna assembly.
  • Use the flat end of a spudger to pry up the lower antenna assembly and free it from the phone.

  • Remove the antenna assembly.

See that little circular rubber near the bottom right screw? This funnels the background noise to one of the noise canceling microphones. It will be destroyed when you take it off. Freaked me out when I first opened up mine.

Adrian Koch - Reply

Image 1/3: Use the flat end of a spudger to disconnect the NFC antenna cable connector.
  • Insert the tip of a spudger under the battery cable near the connector to lift it straight up from its socket.

  • Use the flat end of a spudger to disconnect the NFC antenna cable connector.

Add Comment

Image 1/3: Slide the tip of the spudger under the button assembly cable near the connector to pull the cable straight out of its socket.
  • Use the tip of a spudger to flip up the ZIF retaining flap from the button assembly cable connector.

  • Slide the tip of the spudger under the button assembly cable near the connector to pull the cable straight out of its socket.

This flap can pop off and get lost, be very gentle when prying it up. I lost mine, and have tape and some paper holding my connection together. Probably not very fire safe, but the stupid phone works.

KQSwift - Reply

Image 1/2:
  • Insert the flat end of a spudger under the interconnect cable to free it from the adhesive holding it to the battery.

I'm not clear on the advantage/purpose of battery removal (steps 24, 25, 26). It can remain attached to the mother board and come away from the phone in tact, eliminating the risk of damage, and the task of dealing with the adhesive, no?

Kelly F - Reply

Image 1/2:
  • Use the flat end of a spudger to peel the adhesive pull-tab off the top of battery.

Add Comment

Image 1/3: The battery is secured to the motherboard with mild adhesive. Peel slowly, and be careful not to bend or puncture the battery.
  • Use the adhesive pull-tab to lift the battery from its recess.

  • The battery is secured to the motherboard with mild adhesive. Peel slowly, and be careful not to bend or puncture the battery.

  • Remove the battery from the phone.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

59 other people completed this guide.

16 Comments

Cool but where to buy the spare battery?

Thanks

Roman Senkyr - Reply

You can buy the spare battery from here: http://www.batterybay.net/Battery-for-Mo...

Minh Nguyen -

Nice, detailed guide. In fact so detailed, I do not trust myself making this repair. Does anyone offer this as a service (for a fee)?

thenikonknight - Reply

OEM is the Motorola EX34, all over Ebay for $12-20

Jeff - Reply

This doesn't address the antenna stuck on (but separate) from the battery. It's easy enough to see in the pictures, but it doesn't come off easily in one piece. I think mine still works, but definitely needs addressing.

Kim Schaffer - Reply

Yes - getting the antenna off is a bear. I - well, my cell-phone guy - didn't bother because I don't use NFC for anything, so I hope that was okay!

Jessica Montena - Reply

Thanks for the guide...I'm wondering how to re-attach the back cover? Did you warm up the adhesive with the iOpener before snapping it back on?

greentree8 - Reply

I didn't need to heat up my phone to remove the back cover. There was some adhesive but nothing ridiculous. For those that are wondering, your phone will work fine without the NFC antenna (assuming you don't want to use NFC) that is affixed to the battery.

Mike - Reply

I had a hard time with the adhesive on the back. I had to heat it more than specified and use the spudger to slowly separate the layers.

ike9898 - Reply

Hi i was wondering if anyone could answer me am i able to use the X1058 batter on a moto x thats X1060

Dylan Mendoza - Reply

I was unable to remove the back cover without causing small cracks.

The iOpener sort of worked but I ended up using a mini hair dryer I had, directing the airflow inside the phone to open it.

If you are not very near sighted, don't try this without a magnifier stand.

A suction cup came in the iFixit kit. The proper use of it should be shown in the instructions. There were a few other parts that came in the kit but I did not use, but later realized they might be helpful. The instructions should show their use.

iFixit might consider selling for say $5 a glossy paper copy of the instructions.

The battery in my phone has Revision B printed on it. The battery I bought of eBay had Revision A on it. iFixit should let readers know what the difference is if any. The battery I got had an antenna and some other parts on it. In general iFixit should give better battery selection and purchase advice.

GX5E - Reply

Performed the battery replacement tonight. Took a risk removing the back cover without applying heat ... the adhesive came loose with a little patience (although I did end up with a small crack to the side of the back cover ... shouldn't be a problem since I use the phone with a case anyway).

Thank you iFixit for this guide including the great photos!

jdaun - Reply

Thank you!!!!!!!

chriserea - Reply

My battery is starting to discharge faster lately, which is over two years old. But looking at this guide and trying to change a broken screen on a moto x once before this is not for the unskilled, butter fingers, etc. I also found out the glass screen is glued to the display so essentially its non serviceable . Then there is the annoying problem of the phone dropping the wifi (no other device in the house has this problem). I tried several corrections found on the internet, nothing has worked. BUY ANOTHER PHONE.

sr71habu - Reply

I absolutely could not get the four T3 screws to come out. They stripped almost immediately so i had to drill the heads of the screws. Thankfully the phone still worked. Put a little dab of super glue in place of the screws.

Our Junk Mail - Reply

I just made the change, but the battery improvement is little. Is it necessary to make a factory reset?

Domingo Echenique - Reply

Add Comment