iPod Touch 5th Generation LCD Shield Plate Replacement

Remove the metal shield plate separating the LCD from the internal components in your iPod Touch 5th Generation.

Use this guide to remove the metal shield plate and gain access to the iPod's internal components.

Edit Step 1 Front Panel  ¶ 

Image #1

Edit Step 1 Front Panel  ¶ 

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

  • Lay overlapping strips of clear packing tape over the iPod's display until the whole face is covered.

    • This will keep glass shards contained and provide structural integrity when prying and lifting the display.

  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.

Edit Step 2  ¶ 

Image #1

Edit Step 2  ¶ 

  • Center the suction cup on the lower section of the glass, with its edge centered over the home button.

  • Press in firmly and make sure the cup has a strong seal.

Edit Step 3  ¶ 

Image #1

Edit Step 3  ¶ 

  • Hold the iPod firmly against a table or bench.

    • Place your thumb and index finger over the lower corners of the display to stop the display from opening too far when the adhesive breaks.

  • Lift the suction cup up and back toward the top of the iPod. Be patient, and pull with firm, constant force until the adhesive breaks and the display comes up from the rear case.

    • After the display begins to lift from the rear case, be careful not to lift more than about an inch—a fragile plastic frame still connects the display assembly to the rear case.

Edit Step 4  ¶ 

Image #1

Edit Step 4  ¶ 

  • In the following steps, you will be loosening and freeing the plastic frame that surrounds the screen. It is connected to the rear case with several clips.

  • Starting at the top right of the device, insert a plastic opening tool into the gap between the plastic frame and the aluminum rear case.

  • Slide the tool down this crack, loosening the frame from the case.

Edit Step 5  ¶ 

Image #1

Edit Step 5  ¶ 

  • Insert the plastic opening tool between the frame and the rear case behind the first clip.

  • Rock the tool sideways, to spread the gap behind the clip and separate it from the rear case.

  • This may not free the clip initially, but repeating the procedure for each clip will begin to loosen the piece.

Edit Step 6  ¶ 

Image #1

Edit Step 6  ¶ 

  • Repeat the procedure with the next two clips on this side.

  • You may have to go back and forth between the clips to free all of them. Take your time and be careful and patient, as the plastic frame is quite fragile.

Edit Step 7  ¶ 

Image #1

Edit Step 7  ¶ 

  • Moving on to the left side of the device, insert a plastic opening tool into the gap between the plastic frame and the aluminum rear case near the top.

  • Slide the tool down this crack, loosening the frame from the case.

Edit Step 8  ¶ 

Image #1

Edit Step 8  ¶ 

  • Insert the plastic opening tool between the frame and the rear case behind the first clip on the left side.

  • Rock the tool sideways, to spread the gap behind the clip and separate it from the rear case.

Edit Step 9  ¶ 

Image #1

Edit Step 9  ¶ 

  • Repeat the procedure with the next two clips on this side.

  • Insert the plastic opening tool between the plastic frame and aluminum rear case behind the second clip.

  • Rock the tool sideways, loosening the clip from the case.

Edit Step 10  ¶ 

Image #1

Edit Step 10  ¶ 

  • Using the same procedure, loosen the last clip securing the plastic frame to the rear case.

Edit Step 11  ¶ 

Image #1

Edit Step 11  ¶ 

  • Insert the plastic opening tool between the display assembly and the rear case near the top of the iPod.

  • Slightly twist the opening tool to pry the front panel up from the rear case.

  • Separate the display assembly from the iPod.

    • Do not try to completely remove the front panel, as it is still connected by several cables.

Edit Step 12 LCD Shield Plate  ¶ 

Image #1

Edit Step 12 LCD Shield Plate  ¶ 

  • Gently fold the display over away from the rest of the iPod, taking care not to disconnect or break any of the ribbon cables. Set the two halves flat on a table or bench.

  • Use a plastic opening tool to pry the home button switch up from the LCD plate.

  • Do not attempt to remove the home button switch, as it is connected to components below the LCD plate.

Edit Step 13  ¶ 

Image #1

Edit Step 13  ¶ 

  • Remove the following screws securing the LCD plate to the rear case:

    • Two 1.2 mm #00 Phillips screws

    • Nine 1.6 mm #00 Phillips screws

    • One 2.3 mm #00 Phillips screw

Edit Step 14  ¶ 

Image #1

Edit Step 14  ¶ 

  • Lift up and remove the LCD plate from the iPod.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the iPod Touch 5th Generation device page.

Required Tools

Phillips #00 Screwdriver

$5.95 · 50+ In stock

Plastic Opening Tools

$2.95 · 50+ In stock

Small Suction Cup

$2.95 · 50+ In stock

Recommended Tools

54 Bit Driver Kit

$24.95 · 50+ In stock

Magnetic Project Mat

$19.95 · 50+ In stock

Pro Tech Screwdriver Set

$59.95 · 50+ In stock

Anti-Static Project Tray

$4.95 · 50+ In stock

Popular Device Products

Comments Comments are onturn off

Step 2.5: Recover iPod from far side of the room due to suction assisted throwing.

thanks, Apple

Nick Hughes, · Reply

Did as shown, button switch works fine, when I reinstall button, it's like it won't touch the switch to engage.

What next?

Gary Aguilera, · Reply

I've got the same problem, managed to get the screen off, transferred the little steel plate to the new home button and put it in. The switch works fine when I press it with my finger, but it won't work with the home button??? - Did you manage to solve this problem?

Tom,

Use the hair dryer or a heat gun to loosen the adhesive. This did not work with just a suction cup for me.

Dmitry Fedoruk, · Reply

All good... But. All I wanted was to replace the cracked camera lens glass. Where in the guide is the instructions for the lens GLASS.

kwylie, · Reply

I also had to use a heat gun and the opening tool instead of just a suction cup to open the assembly. The rest of the guide worked really well!

When putting back together, make sure the display connector is in firm or you might get lines. And also, perform a hard reset - my power wasn't working, I took it apart and checked the power flex cable, but all it needed was a hard reset when put back together.

Tyler Weaver, · Reply

use a razor blade to pry. there is a huge amount of leverage, and the old frame is most likely trash.

trogfield, · Reply

Careful! This piece is super fragile. It really helps to understand the way the clips work. I struggled for 10 min with not a single un-clip, snapped the plastic frame in 2 places because I didn't understand the clips, and as soon as I figured out how they work the piece was off like a prom dress.

The clips are metal n shapes around the outside of the frame. They need to be pushed away from the center of the device to release the frame. You need to get something in between the plastic and clip to release, a guitar pick is probably too thick. A thin opening device would probably work but I used a razor blade. I'm not sure if these clips are on all of the newer Apple devices, but I've never encountered one before (usually work on android devices.)

I hope this helps prevent someone from having to replace the frame.

nlw93, · Reply

If you have trouble lifting the home button switch up with the plastic opening tool, you can try using an opening pick instead.

matthew, · Reply

Hi I just replaced my screen on my ipod touch 5th gen and i connect all the ribbon chords and every thing and when i connect one of the ribbons from the screen to the motherboard the motherboard starts to get hot! The screen isnt actually fully on, I wanted to make sure it turned on before I snapped it back in place. Any ideas? When I disconnect the ribbon the temp goes down. Screen is an OEM screen from Apple. I read somewhere, and i have personally have done it, that you can short the battery on the ipod touch 4th and it fixes it but im not sure on the 5th.

Eddie, · Reply

I have the same problem. I am going to change the battery. I let you to know if it solved the problem. Please let me know if you solve your problem. Thanks

ismael452000, · Reply

Eddie, Did you ever fix this? I have exactly the same issue, Board gets hot and screen remains black. Although i did Hear Siri and iTunes recognises it.

Dave, · Reply

You need to make sure that all the adhesive covers for the battery and the board are on so that it isn't shorting with the metal cover, this may fix some issues with the board / battery heating up a lot and display not working. I just put some electrical tape over the batter solder and screen cables so that it's all in place properly and no shorting of electric terminal points on the board.

Ben Major,

View Statistics:

Today: 5

This Week: 11

This Month: 17

All Time: 7,188