Installing Sony Cyber-shot DSC-P9 Top Button

You're viewing a previously published version of this guide. View latest version

Jul 31, 2013 - 05:21:06

Jan 28, 2014 - 02:50:01 Sep 04, 2013 - 05:42:51 Jul 31, 2013 - 05:21:06 May 30, 2012 - 12:20:36 May 30, 2012 - 12:14:04 May 21, 2012 - 09:12:24 May 21, 2012 - 09:11:42 May 21, 2012 - 09:11:40 May 21, 2012 - 09:08:54 May 21, 2012 - 09:08:52 May 18, 2012 - 09:30:28 May 17, 2012 - 04:49:40 May 16, 2012 - 10:04:35 May 09, 2012 - 03:04:24 May 09, 2012 - 02:56:35 May 09, 2012 - 02:54:21 May 09, 2012 - 02:48:17 May 09, 2012 - 02:48:11 May 09, 2012 - 02:46:26 May 09, 2012 - 02:46:12 May 09, 2012 - 02:45:59 May 09, 2012 - 02:43:57 May 09, 2012 - 02:39:23 May 09, 2012 - 02:30:58 May 09, 2012 - 02:30:28 May 08, 2012 - 07:11:36 May 08, 2012 - 07:11:34 May 08, 2012 - 07:10:45 May 08, 2012 - 07:10:43 May 08, 2012 - 07:08:49 May 08, 2012 - 07:08:47 May 08, 2012 - 07:07:57 May 08, 2012 - 07:07:56 May 08, 2012 - 07:07:19 May 08, 2012 - 07:07:18 May 08, 2012 - 07:06:22

Newer

What you need

Step 1 Battery

Installing Sony Cyber-shot DSC-P9 Top Button, Battery: step 1, image 1 of 1

Slide the battery latch down the side of the camera with your hands.
The latch will automatically pop open.

Step 2

Unlatch the clip over the battery.
The battery will partially pop out.

Step 3

Remove the battery from the camera.

Step 4 Outer Casing

Installing Sony Cyber-shot DSC-P9 Top Button, Outer Casing: step 4, image 1 of 2

Installing Sony Cyber-shot DSC-P9 Top Button, Outer Casing: step 4, image 2 of 2

Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver.
Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.

Step 5

Once the screws are removed, slowly remove the back casing from the rest of the camera.

Step 6

Then, pull the front case away from the rest of the camera.

Step 7

After the casing is removed, the camera should look as shown.

Step 8 Top Button

Installing Sony Cyber-shot DSC-P9 Top Button, Top Button: step 8, image 1 of 1

Remove the 3.0mm Phillips #000 screw above the battery door on the side of the camera.

Step 9

Pull off the pieces of casing located on either side of the top button of the camera.
Both of the two pieces should slide off very easily. Do not force them off.