Fix Your Stuff

Right to Repair

Store

You're viewing a previously published version of this guide.  View latest version

Older
May 17, 2017 - 12:05:13
May 17, 2017 - 12:05:13 May 17, 2017 - 12:05:11 May 17, 2017 - 12:05:52 May 17, 2017 - 12:05:26 May 17, 2017 - 12:05:56 May 17, 2017 - 12:05:41 Apr 23, 2017 - 01:04:33 Apr 23, 2017 - 01:04:12 Apr 23, 2017 - 01:04:46 Apr 23, 2017 - 01:04:15 Apr 21, 2017 - 06:04:01 Apr 19, 2017 - 02:04:12 Apr 19, 2017 - 02:04:03 Apr 19, 2017 - 02:04:38 Apr 19, 2017 - 02:04:21 Apr 19, 2017 - 02:04:44 Apr 19, 2017 - 12:04:10 Apr 19, 2017 - 12:04:53 Apr 19, 2017 - 12:04:37 Apr 19, 2017 - 12:04:16 Apr 19, 2017 - 12:04:19 Apr 19, 2017 - 12:04:06 Apr 19, 2017 - 12:04:55 Apr 18, 2017 - 09:04:41 Apr 17, 2017 - 09:04:31 Apr 17, 2017 - 09:04:54 Apr 12, 2017 - 11:04:29 Apr 12, 2017 - 11:04:49 Apr 12, 2017 - 11:04:18 Apr 12, 2017 - 11:04:38 Apr 12, 2017 - 11:04:46 Apr 12, 2017 - 11:04:27 Apr 12, 2017 - 11:04:53 Apr 12, 2017 - 11:04:44 Apr 10, 2017 - 12:04:09 Apr 10, 2017 - 12:04:20 Apr 10, 2017 - 12:04:04 Apr 10, 2017 - 12:04:42 Apr 10, 2017 - 12:04:42 Apr 10, 2017 - 12:04:32 Apr 10, 2017 - 12:04:17 Apr 10, 2017 - 12:04:51 Apr 10, 2017 - 12:04:43 Apr 10, 2017 - 12:04:05 Apr 10, 2017 - 12:04:33 Apr 10, 2017 - 12:04:19 Apr 10, 2017 - 12:04:02 Apr 10, 2017 - 12:04:03 Apr 10, 2017 - 12:04:32 Apr 10, 2017 - 12:04:48 Apr 10, 2017 - 12:04:21 Apr 10, 2017 - 12:04:46 Apr 10, 2017 - 12:04:16 Apr 10, 2017 - 12:04:07 Apr 10, 2017 - 12:04:20 Apr 10, 2017 - 10:04:21 Apr 10, 2017 - 10:04:10 Apr 10, 2017 - 10:04:50 Apr 10, 2017 - 09:04:56 Apr 10, 2017 - 09:04:51 Apr 10, 2017 - 09:04:27 Apr 10, 2017 - 09:04:10 Apr 10, 2017 - 09:04:22 Apr 10, 2017 - 09:04:07 Apr 10, 2017 - 09:04:31 Apr 10, 2017 - 09:04:50 Apr 10, 2017 - 09:04:19 Apr 10, 2017 - 09:04:50 Apr 10, 2017 - 09:04:40 Apr 10, 2017 - 09:04:15 Apr 10, 2017 - 09:04:01 Apr 10, 2017 - 09:04:35 Apr 10, 2017 - 09:04:27 Apr 10, 2017 - 09:04:34 Apr 10, 2017 - 09:04:33 Apr 10, 2017 - 08:04:44
Newer

Razer DeathAdder Chroma Outer Casing Replacement

Written By: Corrie Tung (and one other contributor)
  • Comments: 0
  • Favorites: 0

Difficulty

Easy

Steps

7

Time Required

4 minutes

Sections

1

Flags

1

Prerequisite Only

Prerequisite Only

Please note that this guide is only a prerequisite for other guides.

Introduction

This is a prerequisite for all DeathAdder Chroma replacement guides.

Tools

Buy these tools

Parts

No parts specified.

  1. Opening the mouse casing will void any warranty that exists for the mouse.

    • Opening the mouse casing will void any warranty that exists for the mouse.

    • Turn the mouse over so the bottom is facing up.

  2. Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges. Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.

    • Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.

  3. Use a Phillips #0 screwdriver to remove two 6.7 mm screws. Use a Phillips #0 screwdriver to remove two 6.7 mm screws.

    • Use a Phillips #0 screwdriver to remove two 6.7 mm screws.

  5. Use your fingers to identify the location of the screw under the bottom label.

    • Use your fingers to identify the location of the screw under the bottom label.

  6. Use a Phillips #0 screwdriver to remove one 6.7 mm screw.

    • Use a Phillips #0 screwdriver to remove one 6.7 mm screw.

    • Clear the label away from around the screw for easier removal.

  7. Turn the mouse over so the bottom is facing down. Separate the top casing from the bottom base by pulling the top casing upwards. Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.

    • Turn the mouse over so the bottom is facing down.

    • Separate the top casing from the bottom base by pulling the top casing upwards.

    • Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.

  8. Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward. Pulling too hard could damage the wire connections.

    • Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward.

    • Pulling too hard could damage the wire connections.

Author

with 1 other contributor

Corrie Tung

Member since: 03/24/2017

543 Reputation

2 Guides authored

Badges: 11

+8 more badges

Team

Baylor, Team S5-G2, Williams Spring 2017 Member of Baylor, Team S5-G2, Williams Spring 2017

BU-WILLIAMS-S17S5G2

3 Members

5 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 4

All Time: 55