IKEA Drill Battery Replacement

You're viewing a previously published version of this guide. View latest version

Jul 31, 2019 - 02:20:00

Jul 31, 2019 - 02:20:00 Jun 12, 2019 - 10:08:07 Jun 12, 2019 - 10:07:59 Jun 12, 2019 - 10:07:16 Jun 12, 2019 - 10:07:08 Jun 12, 2019 - 10:06:44 Jun 07, 2017 - 02:33:56 Jun 07, 2017 - 02:33:55 Jun 07, 2017 - 02:33:33 Jun 07, 2017 - 02:33:17 Jun 07, 2017 - 02:32:24 Mar 24, 2017 - 04:58:01 Mar 24, 2017 - 04:52:17 Mar 23, 2017 - 06:55:43 Mar 15, 2017 - 08:05:13 Mar 15, 2017 - 07:44:45 Mar 15, 2017 - 07:43:15 Mar 15, 2017 - 07:34:09 Mar 15, 2017 - 07:32:52 Mar 15, 2017 - 07:32:46 Mar 15, 2017 - 07:30:40 Mar 15, 2017 - 07:30:14 Mar 15, 2017 - 07:28:16 Mar 15, 2017 - 07:27:06 Mar 15, 2017 - 07:26:35 Mar 15, 2017 - 07:26:00 Mar 15, 2017 - 07:24:35 Mar 15, 2017 - 07:23:49 Mar 15, 2017 - 07:17:20 Mar 15, 2017 - 07:15:08 Mar 15, 2017 - 07:14:31 Mar 15, 2017 - 07:14:04 Mar 15, 2017 - 07:13:22 Mar 15, 2017 - 06:56:20 Mar 15, 2017 - 06:50:31 Mar 15, 2017 - 06:45:52 Mar 15, 2017 - 06:43:59 Mar 15, 2017 - 06:33:37 Mar 15, 2017 - 06:32:16 Mar 15, 2017 - 06:28:48 Mar 15, 2017 - 06:26:00 Mar 15, 2017 - 06:20:36 Mar 15, 2017 - 06:15:39 Mar 15, 2017 - 06:12:17 Mar 15, 2017 - 05:57:41 Mar 15, 2017 - 04:24:56

Newer

Introduction

The requirements for replacing the battery are the usage of a 4 mm Phillips screwdriver, a soldering iron station, a utility knife, heat shrink tubes and two lithium batteries (3.6 V). Make sure how to use a soldering iron, especially in combination with batteries. If you are not familiar with (replacing) batteries, it might be a good idea to search for some information about how batteries work. Last but not least, create a work environment with good lighting and a clean desk. The replacement requires attention and concentration.

What you need

Step 1 Battery

IKEA Drill Battery Replacement, Battery: step 1, image 1 of 1

Use a 4 mm Phillips screwdriver to remove the seven screws to disassemble the housing of the drill.

Step 2

Remove the sticker carefully from the bottom.

Step 3

Open the housing of the drill.
While opening place the rotation switch apart.
Detach the electric circuit and place it next to the drill.

Step 4

Cut each tubing from the three wires of the battery with a utility knife.

Step 5

Disconnect the three wires of the battery with a soldering iron.

Step 6

Place each new tubing (three in total) on the battery wires through sliding them on each wire.

Step 7

Attach the two batteries to each other with tape, in case you have two separate batteries.
Use solder and a solder iron to attach the new battery to the wires.
The black wire should be connected with the negative pole of the two-wire side.
The wire should be warm enough to solder the battery to the wire.
Slide the tubings on each connection and heat each tubing with a lighter to make them shrink.