Introduction

After getting into the Hannspad, the Camera is fairly easy to replace.

Turn the device off.
  • Turn the device off.

  • Place the tablet screen side up.

  • Make sure the device is turned off to avoid damage.

Add Comment

Use the metal spudger to press an opening between screen and back cover. Plastic tabs
  • Use the metal spudger to press an opening between screen and back cover.

  • Plastic tabs

  • Be careful, as the plastic tabs are delicate.

Add Comment

Wedge the plastic opening tool between the screen and the back panel to keep tension constant.
  • Wedge the plastic opening tool between the screen and the back panel to keep tension constant.

Add Comment

Slide the metal spudger around the casing to separate it from the inside of the tablet. Slide the metal spudger around the casing to separate it from the inside of the tablet.
  • Slide the metal spudger around the casing to separate it from the inside of the tablet.

Add Comment

After all the tabs are separated, flip tablet over so the screen side is down. Remove the back panel by delicately lifting straight up.
  • After all the tabs are separated, flip tablet over so the screen side is down.

  • Remove the back panel by delicately lifting straight up.

Add Comment

Identify the DC power connection cables. Remove the adhesive tape. Battery
  • Identify the DC power connection cables.

  • Remove the adhesive tape.

  • Battery

  • Battery power conections

Add Comment

Use the tweezers to grab hold of the red wire and desolder the connection to the circuit board. The soldering iron is hot, and will cause the wires and motherboard to heat up. Instructions for desoldering can be found on iFixit's page Soldering
  • Use the tweezers to grab hold of the red wire and desolder the connection to the circuit board.

  • The soldering iron is hot, and will cause the wires and motherboard to heat up.

  • Instructions for desoldering can be found on iFixit's page Soldering

Add Comment

Use the tweezers to grab  the black wire and desolder the connection. Do not let the ends of the black and red wires touch. Do not let the ends of the black and red wires touch.
  • Use the tweezers to grab the black wire and desolder the connection.

  • Do not let the ends of the black and red wires touch.

Add Comment

Desolder the connection, while using the tweezers to grab hold of the yellow wire. Desolder the connection, while using the tweezers to grab hold of the yellow wire. Desolder the connection, while using the tweezers to grab hold of the yellow wire.
  • Desolder the connection, while using the tweezers to grab hold of the yellow wire.

Add Comment

The battery is attached to the tablet with an adhesive. Use the flat end of the plastic spudger to peel the battery off the tablet The battery is attached to the tablet with an adhesive. Use the flat end of the plastic spudger to peel the battery off the tablet The battery is attached to the tablet with an adhesive. Use the flat end of the plastic spudger to peel the battery off the tablet
  • The battery is attached to the tablet with an adhesive. Use the flat end of the plastic spudger to peel the battery off the tablet

Add Comment

Identify the ribbon connecter attached to the camera and where it connects to the circuit board. The two cameras are connected with one ribbon cable.
  • Identify the ribbon connecter attached to the camera and where it connects to the circuit board.

  • The two cameras are connected with one ribbon cable.

  • Zero insertion force connector.

Add Comment

The sliding zero insertion force (ZIF) connector is easy to disconnect.  Use the plastic opening tool or a fingernail to slide the tab out, then pull the cable out. The sliding zero insertion force (ZIF) connector is easy to disconnect.  Use the plastic opening tool or a fingernail to slide the tab out, then pull the cable out. The sliding zero insertion force (ZIF) connector is easy to disconnect.  Use the plastic opening tool or a fingernail to slide the tab out, then pull the cable out.
  • The sliding zero insertion force (ZIF) connector is easy to disconnect. Use the plastic opening tool or a fingernail to slide the tab out, then pull the cable out.

Add Comment

Pull the cameras out of their resting places in a straight upward motion. Pull the cameras out of their resting places in a straight upward motion. Pull the cameras out of their resting places in a straight upward motion.
  • Pull the cameras out of their resting places in a straight upward motion.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

matthew vandeventer

Member since: 03/11/2015

824 Reputation

5 Guides authored

Team

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 3

Past 30 Days: 5

All Time: 317