Skip to main content

Fix Your Stuff

Right to Repair

Store

Introduction

Use this guide to replace the face buttons on your Backbone One.

  1. Use a Phillips screwdriver to remove the four 5.9 mm-long screws.
    • Use a Phillips screwdriver to remove the four 5.9 mm-long screws.

  2. Lift up the upper cover of the controller. Swing the upper cover over and place it on the controller case. Make sure that the interconnecting cable has no tension.
    • Lift up the upper cover of the controller.

    • Swing the upper cover over and place it on the controller case.

    • Make sure that the interconnecting cable has no tension.

  3. Use a pair of tweezers to remove the yellow protective tape which is placed over the interconnect cable and the connector. Use a pair of tweezers to remove the yellow protective tape which is placed over the interconnect cable and the connector. Use a pair of tweezers to remove the yellow protective tape which is placed over the interconnect cable and the connector.
    • Use a pair of tweezers to remove the yellow protective tape which is placed over the interconnect cable and the connector.

  4. Use the tip of an opening pick to open the gray flap of the interconnect cable ZIF connector by pushing it upwards. Use the tip of an opening pick to open the gray flap of the interconnect cable ZIF connector by pushing it upwards. Use the tip of an opening pick to open the gray flap of the interconnect cable ZIF connector by pushing it upwards.
    • Use the tip of an opening pick to open the gray flap of the interconnect cable ZIF connector by pushing it upwards.

  5. Disconnect the cable by pulling it straight out the ZIF connector. Disconnect the cable by pulling it straight out the ZIF connector.
    • Disconnect the cable by pulling it straight out the ZIF connector.

  6. Use a pair of tweezers to disconnect the phone connector cables out from their sockets. Use a pair of tweezers to disconnect the phone connector cables out from their sockets. Use a pair of tweezers to disconnect the phone connector cables out from their sockets.
    • Use a pair of tweezers to disconnect the phone connector cables out from their sockets.

  7. Separate the the upper case of the left controller handle.
    • Separate the the upper case of the left controller handle.

  8. Use a Phillips screwdriver to remove the three 5.9 mm-long screws.
    • Use a Phillips screwdriver to remove the three 5.9 mm-long screws.

  9. Remove the trigger. Remove the trigger.
    • Remove the trigger.

  10. Remove the bumper. Remove the bumper.
    • Remove the bumper.

  11. Use a Phillips screwdriver to remove the two 3.9 mm-long screws.
    • Use a Phillips screwdriver to remove the two 3.9 mm-long screws.

  12. Remove the mainboard. Remove the mainboard. Remove the mainboard.
    • Remove the mainboard.

  13. Use a pair of blunt nose tweezers to remove the rubber cover which is placed over the face buttons. Use a pair of blunt nose tweezers to remove the rubber cover which is placed over the face buttons. Use a pair of blunt nose tweezers to remove the rubber cover which is placed over the face buttons.
    • Use a pair of blunt nose tweezers to remove the rubber cover which is placed over the face buttons.

  14. Use a pair of tweezers to remove the face buttons. Use a pair of tweezers to remove the face buttons. Use a pair of tweezers to remove the face buttons.
    • Use a pair of tweezers to remove the face buttons.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Ask our Answers community for help.

Adriana Zwink

Member since: 12/18/2019

12,657 Reputation

68 Guides authored

Team

iFixit Member of iFixit

Community

134 Members

15,617 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 14

All Time: 17