Skip to main content

This translation may not reflect the most recent updates from the source guide. Help update the translation or view the source guide.

拆卸步骤大全

Prerequisite Only
This guide is only intended to be used as a prerequisite for other guides. It's incomplete by itself.

What you need

  1. 拆卸步骤大全, 五角螺丝: step 1, image 1 of 1
    • 在拆卸iPhone之前,请将电池放电至25%以下。 充电的锂离子电池如果意外被刺破可能会着火和/或爆炸。

    • 在开始拆卸之前请将你手机关机。

    • 将位于Lightning数据口两侧(处于iPhone底部边缘)的2颗3.4 mm的五角螺丝拧下。

  2. 拆卸步骤大全, 拆卸步骤大全: step 2, image 1 of 1
    • 如果你没有反向钳,请遵循以下三步使用吸盘。

    • 可选择使用 iOpener 或吹风机,对 iPhone 下边缘稍加热约一分钟。

    • 加热软化固定屏幕的胶水,可以更容易打开 iPhone。

  3. 拆卸步骤大全: step 3, image 1 of 1
    • 6s 屏幕四个边缘周围有黏胶固定, 若你选择要更换黏胶的话, 在你拆解之前, 最好是先准备好新的黏胶。若你本身不想更换新黏胶也行, 因为在功能上, 跟使用原有的黏胶没有太大差别 。

    • 将吸盘置于屏幕左下角, 进行拆解。

    • 注意, 吸盘放置地方不能与Home键重叠。

  4. 拆卸步骤大全: step 4, image 1 of 2 拆卸步骤大全: step 4, image 2 of 2
    • 使用巧劲拉动吸盘, 直到屏幕与后盖中间出现缝隙为止

    • 在拆解过程需花点时间及控制力道。屏幕因为有黏胶的关系, 会比一般产品来得更紧。

    • 注意, 若拉太大力会造成屏幕损坏。只要打开到让显示屏与后盖有个小缝隙即可。

    • 如果有任何问题,请使用iOpener,吹风机或热风枪加热iPhone正面,直至其变得有点烫手。 这将有助于软化固定显示器边缘的粘合剂。

  5. 拆卸步骤大全: step 5, image 1 of 2 拆卸步骤大全: step 5, image 2 of 2
    • 在屏幕下有个槽口, 位置正好在耳机插槽上方。这里是撬开的最佳位置。

    • 将撬棒平面那头插进屏幕与后盖的缝隙, 也就是耳机插槽上方位置。

  6. 拆卸步骤大全: step 6, image 1 of 2 拆卸步骤大全: step 6, image 2 of 2
    • 用撬棒将缝隙左右边撑开, 使屏幕从机身上分离。

  7. 拆卸步骤大全: step 7, image 1 of 2 拆卸步骤大全: step 7, image 2 of 2
    • 将撬棒平的那头插进手机左侧, 屏幕与背盖间的缝隙。

    • 将撬棒缓慢地往上移动, 使黏胶与机身分离。

  8. 拆卸步骤大全: step 8, image 1 of 2 拆卸步骤大全: step 8, image 2 of 2
    • 移开撬棒后, 再将撬棒重新插入你一开始从手机底部撬开的地方。

    • 将撬棒缓慢地沿着底部边缘移到右边。

  9. 拆卸步骤大全: step 9, image 1 of 2 拆卸步骤大全: step 9, image 2 of 2
    • 将撬棒缓慢地往上移动, 使黏胶与机身分离。

  10. 拆卸步骤大全: step 10, image 1 of 2 拆卸步骤大全: step 10, image 2 of 2
    • 用吸盘将屏幕小心地掀开, 并将剩余黏胶折断。

    • 請勿將屏幕掀开超过90º, 因为屏幕上还有3条排线连接, 如果掀开角度过大, 可能造成排线损坏。

  11. 拆卸步骤大全: step 11, image 1 of 2 拆卸步骤大全: step 11, image 2 of 2
    • 使用巧劲将吸盘往上拉, 将屏幕与机身分离。

  12. 拆卸步骤大全: step 12, image 1 of 3 拆卸步骤大全: step 12, image 2 of 3 拆卸步骤大全: step 12, image 3 of 3
    • 以屏幕顶端为支点,将屏幕缓缓地向上掀起。

    • 将屏幕掀至约90º竖起, 并且在你操作的时候找个东西支撑着它。

    • 用橡皮筋将前面板与支撑物固定住。这可以避免拉扯到显示排线。

    • 若在紧要关头时, 你也可以用未开过的罐装饮料撑着屏幕, 这也是可行方法。

Conclusion

拆解完后要组装的话, 只要按照逆序操作一下步骤。

8 other people completed this guide.

Special thanks to these translators:

en zh

92%

These translators are helping us fix the world! Want to contribute?
Start translating ›

Evan Noronha

Member since: 02/05/15

223,523 Reputation

168 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 6

Past 30 Days: 13

All Time: 1,592