Fix Your Stuff Community Store

Repair guides and support for your Samsung TV.

2610 Questions View all

Options

Samsung LED TV model UA40C6900VMXZK, Not turning ON,

Hi guys,

My samsung LED TV not turning ON, I can hear continuous clicking sound from power relay (on Power board), whenever i unplug main board from power board, clicking sound disappear, but still no light visible even from hole of backside,

NOTE- Not observed any type of over heating, bulged cap, getting stand by voltage 5V.

Power Board model - PD46AF1E_ ZSM BN44 00357A

Block Image

main board model - CN09BN9500411AL003ZCG0024 (LTF400HJO5 - LTJ400HJ05-A)

Block Image

Checked voltage from main board to power board, it's dropping

Prompt reply will be highly appreciated,

Regards

Satendra from INDIA

Answer this question I have this problem too

Is this a good question?

Yes No
Score 1
1 Comment

thanks for reply, but still same problem

by

Add a comment

2 Answers

Filter by:
Most Helpful Newest Oldest
Most Helpful Answer

Options

Satendra g  disconnect the cable going from the main board to the power board. Then turn your TV on. Let us know if your backlight comes on.

TROUBLESHOOTING

No Power

SYMPTOM

The LEDs on the front panel do not work when connecting the power cord.The SMPS relay does not work when connecting the power cord.

The units appears to be dead.

CHECK POINTS

The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:Check the internal cable connection status inside the unit.

Check the fuses of each part.

Check the output voltage of SMPS.

Replace the Main Board.

Check ‘Main power input’ ? - BD1026 : B18VS_PW - BD1020: B13V - BD1023 : B5V

Check Output of ‘Stand-By Power IC’ ? - Pin#3 of IC4 : A3.3V > Change the Main Assy.

Check Input power of ‘T-con b’d’ - F1(T-CON) : B13V > Reconnect or Change the LVDS cable.

Check Power of ‘T-con b’d’. - L9(T-CON) : VCC12 - TP_VCC33 : VCC33  > Change the T-con B’d.

Block Image

If nothing else you want to consider posting some images of all of your boards. that will allow us to see what you see. use this guide Adding images to an existing question for that

Was this answer helpful?

Yes No
Score 3

10 Comments:

hii, oldturkey, i disconnected cable which come from main board no light visibile at all. ??????. i attached pic of power and main board for further action. thanks

by

You backlight gets the power from the power board after receiving the enable backlight signal from the main board. When you disconnect the mainboard from the power board, your backlight should come on. Since this is not happening, it is most likely that the issue is your power board. Check the fuses on your power board for continuity.

by

But checked voltage from main board back to power board, it's dropping. Like 5 v then 12 V again 5V

by

Satendra g where are you checking the voltage and nder waht condition. TV on/off etc.

by

I m checking in ON condition, On T- board, however after removing cable of main board clicking sound disappeared, but backlight still didn't ON

by

Show 5 more comments

Add a comment

Options

The power board is broken ,I think you can have a look this

https://www.abctay.com/vizio-dps200pp190...

Was this answer helpful?

Yes No
Score 0

1 Comment:

hii jesus, how can u say that, power board is fine and getting 5 V from main board, power relay continuously clicking. Thanks for reply. awaitig some more info from you.

by

Add a comment

Add your answer

Satendra g will be eternally grateful.
View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 1

All Time: 637