Jonny

Hey, I got an customer that I have changed screen on there iphone 7. After a while it started flickering and the bottom of...

Has anyone tested this charging port with working home button for iPhone 7? Should also charge 50% faster with this...

Iphone 6s where the homebutton diddnt work with pressning function but touch id did work. Replaced The homebutton. But if...

Hey, is there any way to get past the frp lock? Got the right email and password but it then asks to sign in with an owner...

Hey, is there any way to see if the homebutton is original? Got one that dosent work but i dont know if they replaced it...

Hey, I have Recived a dead iPhone 7 that I got 24h to look at and need to decide if I want to buy it before that time...

The iPhone 5S gets message "iPhone' could not be restored. an unknown error occurred -1" when trying to restore, it goes...

Hey, I did get a free iPhone 6 that randomly started do the Apple logo reboot. I found out that if I connect it to a...

Hey, I'm looking on an Samsung s2 (9100) that been dropped and after that it starts a few seconds then gives a message...

What is that white part called? need a new one for a 6s pcb i bought water damaged and someone had almost broken it off...

There is a new homebutton that you can use that has the click function (home) but touch id dosent work, dosent need to change the charging port to use the newest replacing homebutton, just replace the homebutton. If you want touch id to work a part of the flex cable need to be changed (microsolder)

Check so the metal part on the screens flex cables dosent hit the speaker or the motherboard when clicking it back in the housing. If the screen isen't up a bit on the right lower side when its in place test with a small piece of tape on each side of that part on the flex or directly at the speaker/motherboard. I have had the same problem once and then it hit the speaker a bit. so released the plate and moved the flax cables a bit higher

Did you unplugg the battery every time you replaced the screen? If not, I would check the lightning/image fuse

The homebutton and touch id wont work when replacing the homebutton on iphone 7&7+. Test a hardreset (power button and volume down) and if that dosent work test to unplugg the homebutton, and if that dosent help test unplugging the front camera.

It looks like the glas have seperated from the plastic, the screews need to be removed to open it. If the glas gets moved upwards more you may breake something like the homebutton or screen glas.

Im not sure about iphone 6 but i know one iphone 5S that did get reversed problem, no music sound but ear speaker worked. A small metal part did get bended when the battery connector was set down . remove the battery connector and the lightning connector and around that there is smal protecting tape, remove that and look around the battery connector if you see any metal parts or components that are bended/moved or hits any other component.

Hey have you tested a hard reset? Hold power button and home button the same time up to a minute, relese when you see the apple logo. If that dosent work, I would open it up, relse the plate over the connectors for the battery and lightning and look if anything looks damaged on the board

Did this happen from no where or after drop / any part replaced? have you cleaned the upper part of the screen? it is two diffrent sensors on same flex cable for the auto brightness and to shut down the screen when in a call. if something is above that sensor or screen is replaced and its not enught light in to that sensor it will go black at once and stop when the call ends. It can also be a defective sensor. Heres how you replace it: iPhone 6s Front-Facing Camera and Sensor Assembly Replacement

Hey, there isent any photos here. IPhone 7&7+ sometimes dosent start without homebutton or the front camera connected (broken=not connected) . Did you test an hard reset? Power button and volume down button up to a minute, if you see the Apple logo the release the buttons. Can you fix the photos?

Have you checked the port for dirt/dust? It's very common on aux and charging port