thefluffyfist

@thefluffyfist

thefluffyfist

608	Reputation
20	Solutions
2	Guides
Member Since 04/08/2017

I like turtles

Votes

Teardowns I've Worked On

RedOctane X-Plorer Teardown

My Guides

Logitech G710+ Disassembly

Guides I've Contributed To

PlayStation 3 Hard Drive Replacement

PlayStation 3 Control Board Replacement

RedOctane X-Plorer Rear Case Replacement

Completed Guides

Yellow Light of Death Repair

PlayStation 3 Hard Drive Replacement

Logitech G710+ Disassembly

Dell Inspiron 15-3521 Hard Drive Replacement

Questions

What is required to get a picture? 03/23/2019
I recently did a teardown of my ps3 and put it back together but, its not working. I just wanted to know what components...

Answers

Answer to "I have a Hummer Truck starting to blow heavy white smoke from tailpipe" 04/03/2019
From the details that you have given the problem is either a blown head gasket or a blown head. THIS SHOULD BE REPAIRED IMMEDIATELY! This is caused by coolant getting into the cylinder and coolant being burned. That is why it is a very chemically smell and burns the eyes. I would suggest taking the vehicle to your local mechanic and they can do the repair. This repair should only be done by someone that knows what he is doing.
Answer to "Battery percentage suddenly drops from ~60% to 7%" 03/30/2019
the censers that control the % of battery may be shot or they may not be wired up correctly
Answer to "kenmore Elite error code F-25" 03/30/2019
F25 is a communication error between the mcu(motor control unit) and the main board . it could be alot of things as quoted from @oldturkey03 : If the control is unable to properly detect motor speed, the machine shuts down. If a failure occurs during high-speed spin, the door unlocks after 3 Minutes. Possible Causes/Procedure 1. Verify the shipping system including shipping bolts, spacers and the power cord are removed. 2. Unplug washer or disconnect power. 3. Check drive motor tachometer resistance. It should be approx. 115 ohms. 4. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 5. Plug in washer or reconnect power. 6. Check the MCU by looking for operations of the drive motor. 7. Check the drive motor for powered rotations. If everything checks out okay, you should think about replacing the MCU since it may not read your motor correctly. Download the service manual from the bottom of this page.
Answer to "Why is there a delay in my Club Car when I depress the gas pedal?" 03/30/2019
If it is gas then the clutch may be worn out or if its the kind that turn off every time you stop it may just be old. If it is electric then it may just be getting old
Answer to "How to disable shortcuts?" 03/30/2019
The shortcut should be in the Keyboard Control Panel in the tab settings Shortcuts clicking on the Keyboard section. If it is not in there it might not be disable-able
Answer to "troybilt pony starts for a few seconds then stops" 03/30/2019
If you have tried all of those then maybe the spark plug wires or electrical systems are not making good contact. I would clean the contacts of the wires and if you have a multimeter use it to make sure the wires are working properly.
Answer to "No Service, but Bluetooth and WiFi working" 11/21/2018
The SIM is probably fried.
Answer to "Why does my carburetor overflow gasoline? I have new needles and seat" 11/21/2018
The carbs float is probably clogged.
Answer to "Laptop won’t start not charging either" 11/21/2018
The mother board might be fried or the power supply is fried in some way.
Answer to "The fan does not work" 11/21/2018
Do a guide on replacing it at: iMac Intel 27" EMC 2309 & 2374

Page 1 of 2

Reputation Breakdown

Event	Count	Delta
Admin approved your guide	2	264
Post was voted up	16	192
Someone completed your guide	10	135
Answer accepted	1	30
Patrolled edit to guide accepted	2	2
Patrolled edit to guide step accepted	1	1
Categorization accepted	1	1
Post was voted down	3	-18