iPad 3 4G Power & Volume Button Assembly Replacement

You're viewing a previously published version of this guide. View latest version

May 15, 2019 - 07:21:08

May 15, 2019 - 07:21:08 Oct 28, 2015 - 07:52:32 Oct 28, 2015 - 07:52:32 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 28, 2015 - 07:52:31 Oct 09, 2013 - 01:25:45 Oct 09, 2013 - 01:16:56 Sep 04, 2013 - 05:36:27 Jul 31, 2013 - 05:08:49 Apr 02, 2013 - 04:09:08 Apr 02, 2013 - 04:08:45 Apr 02, 2013 - 01:53:20 Oct 17, 2012 - 02:27:03 Oct 17, 2012 - 02:27:01 Apr 17, 2012 - 06:56:55 Apr 17, 2012 - 06:56:39 Apr 17, 2012 - 06:56:36 Apr 17, 2012 - 06:55:14 Apr 17, 2012 - 06:55:11 Apr 17, 2012 - 06:53:58 Apr 17, 2012 - 06:53:57 Apr 17, 2012 - 06:51:42 Apr 17, 2012 - 06:51:41 Apr 17, 2012 - 06:47:37 Apr 17, 2012 - 06:47:34 Apr 17, 2012 - 06:45:16 Apr 17, 2012 - 06:45:12 Apr 17, 2012 - 06:42:35 Apr 17, 2012 - 06:42:33 Apr 17, 2012 - 06:38:33 Apr 17, 2012 - 06:38:30 Apr 17, 2012 - 06:36:36 Apr 17, 2012 - 06:36:33 Apr 17, 2012 - 06:17:56

Newer

Introduction

Internal Prereq

What you need

Step 1 Power & Volume Button Assembly

iPad 3 4G Power & Volume Button Assembly Replacement, Power & Volume Button Assembly: step 1, image 1 of 1

Remove the following screws securing the power & volume button cable to the aluminum frame:
Two 5.5 mm Phillips #0
One 2.6 mm Phillips #0
Two 2.6 mm Phillips #0
The two screws located on top are angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

Step 2

Remove the piece of plastic covering the volume buttons.

Step 3

Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.
This screw is angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

Step 4

Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.
Move the plastic opening tool around the sensor, releasing the adhesive.

Step 5

Slide a spudger underneath the power & volume cables, releasing the adhesive.

Step 6

Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.

Step 7

iPad 3 4G Power & Volume Button Assembly Replacement: step 7, image 3 of 3

Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.

Step 8

With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.

Step 9

Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.
Lift and remove the power & volume button cable out of the rear aluminum case.