Introduction

Change out the entire display assembly, including the inverter, hinges, and plastic casing.

Use a coin to turn both battery locking screws 90 degrees to the left.
  • Use a coin to turn both battery locking screws 90 degrees to the left.

  • Remove the battery cover.

  • Remove the battery from the computer by pulling up on the plastic tab.

Add Comment

Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free. Note that the keyboard ribbon is still attached to the logic board, so you cannot completely remove the keyboard yet.
  • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free. Note that the keyboard ribbon is still attached to the logic board, so you cannot completely remove the keyboard yet.

  • If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (between F4 and F5 key) 180 degrees in either direction and try again.

  • Rotate the keyboard away from the screen and rest it face-down on the trackpad area.

Add Comment

If your computer does not have an airport card, you can skip the next two steps.
  • If your computer does not have an airport card, you can skip the next two steps.

  • Grasp the clear plastic tab on the airport card and pull up and toward the display.

Add Comment

Hold the airport card in one hand and use your other hand to remove the antenna cable.
  • Hold the airport card in one hand and use your other hand to remove the antenna cable.

Add Comment

Remove the two Phillips screws that secure the RAM shield.
  • Remove the two Phillips screws that secure the RAM shield.

Add Comment

Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.
  • Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.

Add Comment

Pull up the keyboard connector cable by its clear plastic loop.
  • Pull up the keyboard connector cable by its clear plastic loop.

Add Comment

Use a straightened paperclip to manually eject the CD-ROM tray.
  • Use a straightened paperclip to manually eject the CD-ROM tray.

Add Comment

Turn the computer over so that the bottom is facing up.
  • Turn the computer over so that the bottom is facing up.

  • Remove the following Torx screws:

    • Four short T8 Torx near the battery compartment.

    • Two long T8 Torx near the hinges.

Add Comment

Pull the CD-ROM drive tray partly out.
  • Pull the CD-ROM drive tray partly out.

  • Remove the silver Phillips screw from the plastic casing.

Add Comment

Turn the computer over.
  • Turn the computer over.

  • Remove the three Phillips screws.

Please note: these screws can (and may!) strip easily, so take extra care in removing them!

LambdaCalculus - Reply

This is a diagram of the trackpad ribbon clamp connector you will disconnect in the next step.
  • This is a diagram of the trackpad ribbon clamp connector you will disconnect in the next step.

  • 1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).

  • 2) After disengaging the locking bar, slide the cable out of the connector.

In part 1, you can use a small flat-blade screwdriver to lift the locking bar. This will not put pressure on the cable itself. Each end of the locking bar will click when it has been lifted sufficiently.

Don Solomon - Reply

Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.
  • Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.

  • Slide the orange trackpad ribbon out of the clamp.

Add Comment

Do not lift the upper case too far without first disconnecting the audio cable.
  • Do not lift the upper case too far without first disconnecting the audio cable.

  • Push out the rim of the lower case and pull up on the upper case, grasping it just to the left of the optical drive.

  • Repeat the above step on the upper left corner of the upper case, grasping the bottom left corner of the upper case.

Add Comment

Disconnect the audio cable.
  • Disconnect the audio cable.

Add Comment

Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.
  • Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.

  • You may be thinking you're about to break your upper case. Not to worry - the tabs holding the upper and lower cases together are very strong. Simply apply even pressure and continue to rotate the upper case up and away from the screen until it comes free.

When replacing the upper case, test the trackpad button to make sure it clicks before proceeding. If it does not operate properly, remove the upper case and reattach it.

Don Solomon - Reply

you can use a jimmy klive to open the uppercase

jimmyli564656 - Reply

Remove the following Phillips screws:
  • Remove the following Phillips screws:

    • Remove the longer Phillips screw from the middle-rear of the modem shield.

    • Remove the three identical Phillips screws, two on either side of the EMI fingers, and the remaining one on the right side of the modem shield.

    • Remove the larger Phillips screw that secures the EMI fingers to the modem board.

  • Remove the EMI fingers.

Add Comment

Peel the modem shield away from the metal framework below, working from the right front and moving to the left.
  • Peel the modem shield away from the metal framework below, working from the right front and moving to the left.

Add Comment

Remove the Phillips screw from the left side of the modem.
  • Remove the Phillips screw from the left side of the modem.

  • Pry up the right side of the modem.

Add Comment

Lift the modem partially out and disconnect the cable on the left side.
  • Lift the modem partially out and disconnect the cable on the left side.

Add Comment

Remove the Phillips screw from the left hinge.
  • Remove the Phillips screw from the left hinge.

  • Peel up the airport cable from beneath the yellow tape.

Add Comment

Disconnect the large display data cable from the logic board and deroute it from the plastic and metal tabs.
  • Disconnect the large display data cable from the logic board and deroute it from the plastic and metal tabs.

Add Comment

Disconnect the backlight cable from the logic board and deroute it.
  • Disconnect the backlight cable from the logic board and deroute it.

Add Comment

Remove the three small Phillips screws from the clutch cover.
  • Remove the three small Phillips screws from the clutch cover.

When reinstalling, hold the display so the clutch cover is flush with the panel below. Make sure no wires are caught before tightening the screws.

Don Solomon - Reply

Finally, support the display with one hand while unscrewing the last Phillips screw from the right hinge (push the display gently down to avoid putting pressure on the screw).
  • Finally, support the display with one hand while unscrewing the last Phillips screw from the right hinge (push the display gently down to avoid putting pressure on the screw).

  • Remove the display assembly.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

7 other people completed this guide.

Attached Documents

iRobot

Member since: 09/24/2009

1 Reputation

726 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 5

Past 30 Days: 25

All Time: 11,072