Skip to main content

Shop the Holiday Gift Guide
Free Shipping on Domestic Orders $75+

Xbox One S IR Blaster and Wireless Controller Replacement

Views: 8.5K

View statistics:

Past 24 Hours:
1
Past 7 Days:
38
Past 30 Days:
210
All Time:
8,486
Comments: 20

18 comments on steps, 2 guide comments.

Go to guide comments
Completed: 17

17 people have marked this guide "completed." Will you be next?

Favorites: 0

No one has favorited (and subscribed to) this guide. Will you be the first?

Time Required: 10 - 20 minutes
Difficulty: Moderate
Xbox One S IR Blaster and Wireless Controller Replacement

Introduction

Go to step 1 ↓

This is the wireless connection for the Xbox controllers and Headsets with the Xbox Series One S. You'll notice it has a Wifi mac address. Headsets and controllers disconnecting is a symptom of this card having issues. It's possible removing the card, cleaning the contacts, and reseating will return the card to normal behavior before ordering a replacement.

If your Xbox One S is not picking up motion signals when playing certain games follow this guide to replace your IR blaster. Make sure to check that you are within line of sight of the front of the Xbox One S and there is no barrier between the user and the device.

What you need

Parts

Tools

    1. Xbox One S IR Blaster and Wireless Controller Replacement, Case: step 1, image 1 of 1
      • Flip the Xbox One S so that the bottom of the case is facing upward.

      Ask FixBot

      Add Comment

    2. Xbox One S IR Blaster and Wireless Controller Replacement: step 2, image 1 of 1
      • Begin by working at the case on the rear where the warranty sticker is located. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place. Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

      • Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

      • You will hear clicking sounds when you are prying the case open. It may be fairly difficult to remove the bottom.

      • It's possible that the clips may break when you remove the bottom from the case.

      • We recommend starting at the back where the warranty sticker is located. Pry along the rear edge until all clips are free. From there do each side. When three sides are free start at the end of the front opposite the sync button. Be cautious and take your time and all should separate without any damage.

      Ask FixBot

      Add Comment

    3. Xbox One S IR Blaster and Wireless Controller Replacement: step 3, image 1 of 1
      • Once all of the clips are opened, remove the bottom part of the case.

      Ask FixBot

      Add Comment

    4. Xbox One S IR Blaster and Wireless Controller Replacement: step 4, image 1 of 2 Xbox One S IR Blaster and Wireless Controller Replacement: step 4, image 2 of 2
      • Use a T10 Torx screwdriver to remove the six green 50 mm long screws from the metal case labeled F1 through F6.

      Ask FixBot

      Add Comment

    5. Xbox One S IR Blaster and Wireless Controller Replacement: step 5, image 1 of 2 Xbox One S IR Blaster and Wireless Controller Replacement: step 5, image 2 of 2
      • Gently separate the interior case from the white exterior case using the appropriate method.

      • Pry the white plastic sides outwards at the rear to separate from the plastic I/O shield.

      Ask FixBot

      Add Comment

    1. Xbox One S IR Blaster and Wireless Controller Replacement, IR Blaster and Controller Wireless Connection: step 6, image 1 of 1
      • The IR blaster can be identified on one of the sides of the interior case. It will be next to the disc drive and near the fan.

      Ask FixBot

      Add Comment

    2. Xbox One S IR Blaster and Wireless Controller Replacement: step 7, image 1 of 1
      • Use a Torx T8 screwdriver to remove the four 15 mm screws with orange circles around them.

      • Gently pull the IR blaster off the case.

      Ask FixBot

      Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

17 other people completed this guide.

Author

with

Christopher Chen

Member since: 04/26/17

737 Reputation

2 Guides authored

Team

Cal Poly, Team S22-G3, Livingston Spring 2017 Member of Cal Poly, Team S22-G3, Livingston Spring 2017

CPSU-LIVINGSTON-S17S22G3

4 Members

132 Guides authored

2 Guide Comments

When the board gets replaced does the power light still function normally? I just replaced one because a power button failed and while the new switches work the indicator lights will not power on

Brandon Shrader - Reply Share

Question. What's size and type of button does this board use? I have one with the eject and sync button sheered off.

Frank urmom - Reply Share

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 38

Past 30 Days: 210

All Time: 8,486