Introduction

Use this guide to replace the RF module in your Xbox 360 E.

Parts

No parts required.

Image 1/1: Pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
  • Push the Spudger into the crevice between the grated top panel of the Xbox and the bottom body with the rubber feet.

  • Pull back on the spudger like a lever, keeping it pressed firmly into the crevice.

Add Comment

Image 1/1: Periodically pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
  • Slide the spudger along the separation you have created between the grated panel and the bottom body of the Xbox.

  • Periodically pull back on the spudger like a lever, keeping it pressed firmly into the crevice.

Add Comment

Image 1/3: Pull the top panel off. Image 2/3: Pull the top panel off. Image 3/3: Pull the top panel off.
  • Continue sliding the spudger along the perimeter of the left grated face of the Xbox.

  • Pull the top panel off.

Add Comment

Image 1/1: Pull up on the spudger like a lever, keeping it pressed firmly into the crevice.
  • Push the spudger into the crevice between the right grated face and the top body of the Xbox. It's easier to begin away from the vent.

  • Pull up on the spudger like a lever, keeping it pressed firmly into the crevice.

Add Comment

Image 1/2: Image 2/2:
  • Slide the spudger along the crevice to separate the grated face and the top body.

Add Comment

Image 1/3: Slide the spudger along the crevice, going completely about the perimeter of the bottom panel. Image 2/3: Pull the bottom panel off. Image 3/3: Pull the bottom panel off.
  • Wiggle the spudger in the crevice as you slide the spudger to loosen the bottom plate.

  • Slide the spudger along the crevice, going completely about the perimeter of the bottom panel.

  • Pull the bottom panel off.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • In front of the CD drive you will find the Xbox logo. Press on the area left of the Xbox logo, and the disk tray panel will pop off.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Beginning on the left side without the grate, run the spudger along the crevice until you've reached the grated part, while holding the part that's being separated as you go.

Add Comment

Image 1/3: Rotate the Xbox to the left to locate the clip connecting the front panel to the body. Insert the spudger inside the gap to release the clip. This may require wiggling the spudger. The clip will pop off, making the front panel looser. Image 2/3: Rotate the Xbox to the left to locate the clip connecting the front panel to the body. Insert the spudger inside the gap to release the clip. This may require wiggling the spudger. The clip will pop off, making the front panel looser. Image 3/3: Rotate the Xbox to the left to locate the clip connecting the front panel to the body. Insert the spudger inside the gap to release the clip. This may require wiggling the spudger. The clip will pop off, making the front panel looser.
  • Keep holding the partially separated panel open. It's easiest to do this by wedging a spudger into the opening but can also be held open by your hands.

  • Rotate the Xbox to the left to locate the clip connecting the front panel to the body. Insert the spudger inside the gap to release the clip. This may require wiggling the spudger. The clip will pop off, making the front panel looser.

Add Comment

Image 1/3: Locate the other clip and insert the spudger to remove it. Image 2/3: Locate the other clip and insert the spudger to remove it. Image 3/3: Locate the other clip and insert the spudger to remove it.
  • Flip the Xbox so the opposite side is towards you. Make sure to keep the separation open.

  • Locate the other clip and insert the spudger to remove it.

Add Comment

Image 1/2: Do no pull off the panel too fast because you don't want to damage the ribbon cable. Slowly pull away the panel. Image 2/2: Now that the front panel has been released from its clips you can pull off the front panel.
  • Continue to run the spudger along the crease to release any further clips that may still be attatched.

  • Do no pull off the panel too fast because you don't want to damage the ribbon cable. Slowly pull away the panel.

  • Now that the front panel has been released from its clips you can pull off the front panel.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Find the brown section where the ribbon cable enters the green board. Flip the brown part up and pull out the plastic tab at the end of the ribbon.

Add Comment

Image 1/3: Remove the two 6 mm screws located on the top left and middle right with a T8 Torx screwdriver. Image 2/3: Grip the middle of the green board and gently pull it out. Image 3/3: Grip the middle of the green board and gently pull it out.
  • Looking at the body of the device, locate the green panel to the right of the CD drive.

  • Remove the two 6 mm screws located on the top left and middle right with a T8 Torx screwdriver.

  • Grip the middle of the green board and gently pull it out.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 other people completed this guide.

Sarah

Member since: 01/30/2014

1,241 Reputation

4 Guides authored

Team

Cal Poly, Team 2-11, Amido Winter 2014 Member of Cal Poly, Team 2-11, Amido Winter 2014

CPSU-AMIDO-W14S2G11

4 Members

11 Guides authored

One Comment

Were can I buy an RF module?

Austin Curley - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 3

Past 30 Days: 17

All Time: 1,459