Introduction

This guide will show you how to replace the battery of the Waka Waka Power Plus.

You'll need a 50mm Phillips screwdriver and a flathead screwdriver as thin as possible.
  • You'll need a 50mm Phillips screwdriver and a flathead screwdriver as thin as possible.

Add Comment

Place the Waka Waka with the yellow side up. Flip the standard just as in the right picture. Place the Waka Waka with the yellow side up. Flip the standard just as in the right picture.
  • Place the Waka Waka with the yellow side up. Flip the standard just as in the right picture.

Add Comment

First you remove the two yellow rubbers using your nail or the screwdriver. Than use the Phillips screwdriver to remove the two screws. First you remove the two yellow rubbers using your nail or the screwdriver. Than use the Phillips screwdriver to remove the two screws.
  • First you remove the two yellow rubbers using your nail or the screwdriver. Than use the Phillips screwdriver to remove the two screws.

Add Comment

Turn the Waka Waka upside down. Make sure the Waka Waka is placed on a flat surface. Place the flathead screwdriver between the yellow and the black part as can be seen in the second picture. Force will be needed. If one side came loose, do the same for the other side. Turn the Waka Waka upside down. Make sure the Waka Waka is placed on a flat surface. Place the flathead screwdriver between the yellow and the black part as can be seen in the second picture. Force will be needed. If one side came loose, do the same for the other side. Turn the Waka Waka upside down. Make sure the Waka Waka is placed on a flat surface. Place the flathead screwdriver between the yellow and the black part as can be seen in the second picture. Force will be needed. If one side came loose, do the same for the other side.
  • Turn the Waka Waka upside down. Make sure the Waka Waka is placed on a flat surface. Place the flathead screwdriver between the yellow and the black part as can be seen in the second picture. Force will be needed. If one side came loose, do the same for the other side.

Add Comment

Black Friday
Broken doesn't stand a chance.
Now you see all the components in the Waka Waka. The battery is attached to the case with tape, so you have to use force to pull it off. Now you see all the components in the Waka Waka. The battery is attached to the case with tape, so you have to use force to pull it off. Now you see all the components in the Waka Waka. The battery is attached to the case with tape, so you have to use force to pull it off.
  • Now you see all the components in the Waka Waka. The battery is attached to the case with tape, so you have to use force to pull it off.

Add Comment

Remove the battery from the PCB by pulling the cables out of the clicking system. Remove the battery from the PCB by pulling the cables out of the clicking system.
  • Remove the battery from the PCB by pulling the cables out of the clicking system.

Add Comment

While placing the new battery, make sure the connector is not upside down as you can see in the first picture. Click it in the PCB. While placing the new battery, make sure the connector is not upside down as you can see in the first picture. Click it in the PCB.
  • While placing the new battery, make sure the connector is not upside down as you can see in the first picture. Click it in the PCB.

Add Comment

Use double sided tape to attache the battery to the case. Place the battery back in the case as shown in the second picture. Use double sided tape to attache the battery to the case. Place the battery back in the case as shown in the second picture.
  • Use double sided tape to attache the battery to the case. Place the battery back in the case as shown in the second picture.

Add Comment

Push the electricity cables aside. Place the springs in the case next to the battery. Push the electricity cables aside. Place the springs in the case next to the battery.
  • Push the electricity cables aside. Place the springs in the case next to the battery.

Add Comment

Place the standard. Make sure the standard is placed in the right position.
  • Place the standard. Make sure the standard is placed in the right position.

Add Comment

Place the yellow part above the other half. First push where the springs are placed. Use force. Than push the rest until you hear a click. Place the yellow part above the other half. First push where the springs are placed. Use force. Than push the rest until you hear a click. Place the yellow part above the other half. First push where the springs are placed. Use force. Than push the rest until you hear a click.
  • Place the yellow part above the other half. First push where the springs are placed. Use force. Than push the rest until you hear a click.

Add Comment

Replace the screws and the yellow plugs. Check if everything is working again. Replace the screws and the yellow plugs. Check if everything is working again.
  • Replace the screws and the yellow plugs. Check if everything is working again.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

C2C 2

Member since: 04/01/2015

1 Reputation

1 Guide authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 1

Past 30 Days: 4

All Time: 177