Image 1/3: All screws throughout this guide are the same 3mm size. Image 2/3: All screws throughout this guide are the same 3mm size. Image 3/3: All screws throughout this guide are the same 3mm size.
  • Remove the 3mm screws from bottom of tablet with the precision screwdriver and place on magnetic mat. label where they came from.

  • All screws throughout this guide are the same 3mm size.

Add Comment

Image 1/3: While holding the case open, insert the plastic opening tool to get a larger opening. Image 2/3: Once you have a slight opening, insert the spudger and work around the edges, separating the back plate from the front. Image 3/3: Once you have a slight opening, insert the spudger and work around the edges, separating the back plate from the front.
  • Using the spudger, create a small opening to be used to open the back case.

  • While holding the case open, insert the plastic opening tool to get a larger opening.

  • Once you have a slight opening, insert the spudger and work around the edges, separating the back plate from the front.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • now that the case is open, carefully remove the speakers and set aside.

Add Comment

Image 1/2: Image 2/2:
  • Gently remove the speakers from the back case with tweezers and set the case aside.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Remove yellow tape from surrounding components.

Add Comment

Image 1/3: With the battery separated from the LCD Display, set it aside. Image 2/3: The battery is held down by very strong adhesive. Image 3/3: The battery is held down by very strong adhesive.
  • insert the spudger and gently work around and underneath the battery.

  • With the battery separated from the LCD Display, set it aside.

  • The battery is held down by very strong adhesive.

Add Comment

Image 1/1: Use caution when desoldering to avoid damage to yourself or to the components.
  • Desolder and remove the 2 wires from the motherboard.

  • Use caution when desoldering to avoid damage to yourself or to the components.

Add Comment

Image 1/3: Gently remove the connector by pulling straight out, gripping the black connector head or as close as possible. Image 2/3: Gently grip and pull up the front camera, covered by protective adhesive foam. Image 3/3: Set aside the Camera housing.
  • Locate the Camera Housing. Gently grip and lift the small black tab until you feel an audible click.

  • Gently remove the connector by pulling straight out, gripping the black connector head or as close as possible.

  • Gently grip and pull up the front camera, covered by protective adhesive foam.

  • Set aside the Camera housing.

Add Comment

Image 1/3: Using tweezers, grip the small black tab connected to the white plastic. Image 2/3: Gently lift the tab towards you until it clicks. Image 3/3: Remove the connector by pulling straight out, gripping the black connector head.
  • Locate the LCD Connector.

  • Using tweezers, grip the small black tab connected to the white plastic.

  • Gently lift the tab towards you until it clicks.

  • Remove the connector by pulling straight out, gripping the black connector head.

Add Comment

Image 1/3: Lift the tab towards you until you feel an audible click. Image 2/3: Gently remove the connector by pulling straight out, gripping the black connector head. Image 3/3: Gently remove the connector by pulling straight out, gripping the black connector head.
  • Locate the Touchscreen connector and grip the forward-most black tab with the tweezers.

  • Lift the tab towards you until you feel an audible click.

  • Gently remove the connector by pulling straight out, gripping the black connector head.

Add Comment

Image 1/2: Image 2/2:
  • Gently lift up the WiFi antenna and set aside.

Add Comment

Image 1/2: Gently lift up on the controller and leave it hanging loose. Image 2/2: Gently lift up on the controller and leave it hanging loose.
  • Locate and remove the screws holding the volume and hold button controller. Set screws aside on magnetic mat and label them.

  • Gently lift up on the controller and leave it hanging loose.

Add Comment

Image 1/2: Place on magnetic mat and label them Image 2/2: Gently remove the Motherboard and any wires connected to it and set it aside on a static free surface.
  • Remove screws located on motherboard.

  • Place on magnetic mat and label them

  • Gently remove the Motherboard and any wires connected to it and set it aside on a static free surface.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 other people completed this guide.

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 2

Past 7 Days: 15

Past 30 Days: 55

All Time: 631