Skip to main content

SodaStream Source Internal Disassembly

Prerequisite Only
This guide is only intended to be used as a prerequisite for other guides. It's incomplete by itself.

What you need

  1. SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: step 1, image 1 of 3 SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: step 1, image 2 of 3 SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: step 1, image 3 of 3
    • Push the brass bar, located in the top of the device, out of the carbonating block.

    • You can use the end of your screwdriver to push this piece out.

  2. SodaStream Source  Internal Disassembly: step 2, image 1 of 3 SodaStream Source  Internal Disassembly: step 2, image 2 of 3 SodaStream Source  Internal Disassembly: step 2, image 3 of 3
    • Slide the yellow battery cover up and away to remove it from the device.

  3. SodaStream Source  Internal Disassembly: step 3, image 1 of 2 SodaStream Source  Internal Disassembly: step 3, image 2 of 2
    • Unhook the bottom piece of the plastic arm on each side of the device.

  4. SodaStream Source  Internal Disassembly: step 4, image 1 of 2 SodaStream Source  Internal Disassembly: step 4, image 2 of 2
    • Lift the top of the plastic arm with the spudger and remove it on both sides.

  5. SodaStream Source  Internal Disassembly: step 5, image 1 of 2 SodaStream Source  Internal Disassembly: step 5, image 2 of 2
    • Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.

  6. SodaStream Source  Internal Disassembly: step 6, image 1 of 2 SodaStream Source  Internal Disassembly: step 6, image 2 of 2
    • Remove the plastic oval and the spring within it.

  7. SodaStream Source  Internal Disassembly: step 7, image 1 of 2 SodaStream Source  Internal Disassembly: step 7, image 2 of 2
    • Pull the loader tab cover down and away from the rest of the carbonating block.

  8. SodaStream Source  Internal Disassembly: step 8, image 1 of 1
    • Remove the three 17.9 mm screws located on the right side.

    • These screws may be difficult to access.

  9. SodaStream Source  Internal Disassembly: step 9, image 1 of 2 SodaStream Source  Internal Disassembly: step 9, image 2 of 2
    • Unhook the four clips on the top of the carbonating block and remove the plastic cover.

  10. SodaStream Source  Internal Disassembly: step 10, image 1 of 3 SodaStream Source  Internal Disassembly: step 10, image 2 of 3 SodaStream Source  Internal Disassembly: step 10, image 3 of 3
    • Lift the clips located on both sides with the plastic spudger. Slide the front cover off.

  11. SodaStream Source  Internal Disassembly: step 11, image 1 of 2 SodaStream Source  Internal Disassembly: step 11, image 2 of 2
    • Unhook the silver spring arms on both sides of the device by pushing down.

  12. SodaStream Source  Internal Disassembly: step 12, image 1 of 1
    • Grip the right and left sides of the device and pull it into two identical halves.

    • Once these two pieces are apart, all remaining internal components will fall out of the device.

  13. SodaStream Source  Internal Disassembly: step 13, image 1 of 3 SodaStream Source  Internal Disassembly: step 13, image 2 of 3 SodaStream Source  Internal Disassembly: step 13, image 3 of 3
    • Pull the foam pad up and remove it from the front side of the carbonation component.

  14. SodaStream Source  Internal Disassembly: step 14, image 1 of 1
    • Remove the six 17.7 mm screws from the underside of the loader tab piece.

  15. SodaStream Source  Internal Disassembly: step 15, image 1 of 3 SodaStream Source  Internal Disassembly: step 15, image 2 of 3 SodaStream Source  Internal Disassembly: step 15, image 3 of 3
    • Pull the loader tab out of the nozzle.

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Angela Mossgrove

Member since: 02/20/17

1,072 Reputation

3 Guides authored

Team

USF Tampa, Team S1-G4, Leahy Spring 2017 Member of USF Tampa, Team S1-G4, Leahy Spring 2017

USFT-LEAHY-S17S1G4

3 Members

40 Guides authored

2 Comments

Bonjour j'ai une pièce à l'intérieur dont je ne retrouve pas du tout la position au remontage.

Pouvez vous m'aider ?

Delphine Renard - Reply

De quelle partie s'agit-il, peux-tu prendre une photo ?

Toon Konings - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 0

All Time: 458