Parts

No parts required.

Place the TV face down on a flat smooth surface as to not scratch the screen. Remove the four 8mm screws attaching the stand to the TV.
  • Place the TV face down on a flat smooth surface as to not scratch the screen.

  • Remove the four 8mm screws attaching the stand to the TV.

Add Comment

Lift the stand off the television. Lift the stand off the television.
  • Lift the stand off the television.

Add Comment

Remove the two back panels to display the audio and video inputs.. Remove the two back panels to display the audio and video inputs.. Remove the two back panels to display the audio and video inputs..
  • Remove the two back panels to display the audio and video inputs..

Add Comment

Remove the eight 6mm Phillips screws around the edge. Remove the two 6mm Phillips near the inputs.
  • Remove the eight 6mm Phillips screws around the edge.

  • Remove the two 6mm Phillips near the inputs.

Add Comment

Lift and remove the back case of the television.
  • Lift and remove the back case of the television.

Add Comment

Remove the two speaker cables and the connector from the circuit board by pinching the plastic connectors and firmly pulling up. Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires. Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.
  • Remove the two speaker cables and the connector from the circuit board by pinching the plastic connectors and firmly pulling up.

  • Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.

Add Comment

Remove the green and gray power connector from the side of the buttons panel at the top of the television. Remove the green/gray to orange/gray connector from the center of the circuit board.
  • Remove the green and gray power connector from the side of the buttons panel at the top of the television.

  • Remove the green/gray to orange/gray connector from the center of the circuit board.

Add Comment

Remove the four 5mm phillips screws attaching the LCD and circuit board to the front case. Remove the four 5mm phillips screws attaching the LCD and circuit board to the front case.
  • Remove the four 5mm phillips screws attaching the LCD and circuit board to the front case.

Add Comment

Lift the circuit board/LCD block from the case by lifting the near side of the circuit board and sliding it under the button frame.
  • Lift the circuit board/LCD block from the case by lifting the near side of the circuit board and sliding it under the button frame.

Add Comment

Flip the LCD/circuit board so that the circuit board faces up.
  • Flip the LCD/circuit board so that the circuit board faces up.

Add Comment

Remove the three 5mm Philips screws attaching the circuit board to the LCD. Remove the five 6mm Phillips screws from the edges of the circuit board attacking it to the LCD. Remove the five 6mm Phillips screws from the edges of the circuit board attacking it to the LCD.
  • Remove the three 5mm Philips screws attaching the circuit board to the LCD.

  • Remove the five 6mm Phillips screws from the edges of the circuit board attacking it to the LCD.

Add Comment

Turn the circuit board so the blue and pink side cables are facing you. Hold the white plastic, squeeze and pull from the  sides. Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.
  • Turn the circuit board so the blue and pink side cables are facing you.

  • Hold the white plastic, squeeze and pull from the sides.

  • Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.

Add Comment

Turn the television so the right hand side is facing you. To remove the ribbon cables, fold the brown casing down and pull directly upward on the ribbon. Turn the television so the left hand side is facing you, and remove the ribbon cable in the same manner.
  • Turn the television so the right hand side is facing you.

  • To remove the ribbon cables, fold the brown casing down and pull directly upward on the ribbon.

  • Turn the television so the left hand side is facing you, and remove the ribbon cable in the same manner.

Add Comment

Turn the circuit board so that the left side is facing you. Detach the data cable from the circuit board. To do this, slide your finger nail from the middle of the connector until the little black tabs rotates down toward the board as shown in the second picture.
  • Turn the circuit board so that the left side is facing you.

  • Detach the data cable from the circuit board.

  • To do this, slide your finger nail from the middle of the connector until the little black tabs rotates down toward the board as shown in the second picture.

Add Comment

Lift and remove the circuit board from the LCD frame.
  • Lift and remove the circuit board from the LCD frame.

Add Comment

Now you have your LCD.
  • Now you have your LCD.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 other people completed this guide.

Robert Hobson

Member since: 01/20/2011

1,232 Reputation

9 Guides authored

Team

Cal Poly, Team 1-11, Amido Winter 2011 Member of Cal Poly, Team 1-11, Amido Winter 2011

CPSU-AMIDO-W11S1G11

4 Members

9 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 4

Past 7 Days: 19

Past 30 Days: 88

All Time: 5,946