Slide the lock towards the middle of the camera, in the same direction of the arrow.
  • Slide the lock towards the middle of the camera, in the same direction of the arrow.

Add Comment

Push the blue battery holder up in the direction of the arrow.
  • Push the blue battery holder up in the direction of the arrow.

Add Comment

Pull the battery out of the battery slot.
  • Pull the battery out of the battery slot.

Add Comment

Use tweezers to remove the four rubber screw covers. Use tweezers to remove the four rubber screw covers.
  • Use tweezers to remove the four rubber screw covers.

Add Comment

Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver. Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.
  • Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.

Add Comment

Remove the back casing by just carefully pulling the casing off of the camera.
  • Remove the back casing by just carefully pulling the casing off of the camera.

Add Comment

Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.
  • Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.

Add Comment

Deck the Halls
With tools and Fix Kits
Use plastic opening tool to disconnect screen connector from the control board.
  • Use plastic opening tool to disconnect screen connector from the control board.

Add Comment

Remove the old screen.
  • Remove the old screen.

Add Comment

Remove the 2.381 mm screw with a Phillips #00 screwdriver.
  • Remove the 2.381 mm screw with a Phillips #00 screwdriver.

Add Comment

Use the plastic opening tool to remove the silver metal lens cover.
  • Use the plastic opening tool to remove the silver metal lens cover.

Add Comment

Use the tweezers to remove the black electrical tape covering the copper connector to the control board.
  • Use the tweezers to remove the black electrical tape covering the copper connector to the control board.

Add Comment

From the front of the camera, push the lens through the back of the camer.a
  • From the front of the camera, push the lens through the back of the camer.a

Add Comment

Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors. Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.
  • Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.

Add Comment

Remove the lens assembly from the camera. Remove the lens assembly from the camera.
  • Remove the lens assembly from the camera.

Add Comment

Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.
  • Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.

Add Comment

Use tweezers to pull copper connector from the control board.
  • Use tweezers to pull copper connector from the control board.

Add Comment

Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.
  • Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.

Add Comment

Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.
  • Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Justin Smith

Member since: 03/03/2015

95 Reputation

1 Guide authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 6

All Time: 121