Introduction

You will be required to disassemble much of the printer and its casing. You will need to refer to the Removing Samsung ML2510 Back Panel repair guide.

Image 1/3: Image 2/3: Image 3/3:
  • Remove the hinged top panel by taking the small pins at the bottom of the panel out of their holes.

Add Comment

Image 1/1:
  • Using a Phillips #2 screwdriver, remove the four 1" long, Phillips, PH#2 screws on the back of the printer.

Add Comment

Image 1/3: Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot. Image 2/3: Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot. Image 3/3: Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot.
  • Gently lift the top panel while simultaneously pulling off the back panel.

  • Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Remove front panel by gently moving the holes on the panel from the pegs attached to the main printer body, one at a time.

Add Comment

Image 1/1:
  • Using a Phillips #2 screwdriver, remove the two, 1", Phillips, PH#2 screws on the front face of the printer.

Add Comment

Image 1/3: Repeat process for the other side. Image 2/3: Lift the top panel from the front to remove it entirely. Image 3/3: Lift the top panel from the front to remove it entirely.
  • Using a plastic opening tool, gently lift one side of the top panel from its peg.

  • Repeat process for the other side.

  • Lift the top panel from the front to remove it entirely.

Add Comment

Image 1/3: Gently rotate the panel as indicated in the picture to remove the panel entirely. Image 2/3: Gently rotate the panel as indicated in the picture to remove the panel entirely. Image 3/3: Gently rotate the panel as indicated in the picture to remove the panel entirely.
  • Lift the left side panel up from the raised stops.

  • Gently rotate the panel as indicated in the picture to remove the panel entirely.

Add Comment

Image 1/3: Remove the two, 1", Phillips, PH#2 screws on the back of the printer. Image 2/3: Flip over the metal panel to reveal the gear mechanism. Image 3/3: Flip over the metal panel to reveal the gear mechanism.
  • Using a Phillips #2 screwdriver, remove the five, 1", Phillips, PH#2 screws on the side metal panel.

  • Remove the two, 1", Phillips, PH#2 screws on the back of the printer.

  • Flip over the metal panel to reveal the gear mechanism.

Add Comment

Image 1/3: The entire panel can be removed from the rest of the printer. Image 2/3: Using a Phillips #2 screwdriver, remove the motor from the panel by removing the two, 1", Phillips, PH#2 screws. Image 3/3: Replace the motor and reassemble the printer following instructions in reverse order.
  • Remove the cable attached to the motor.

  • The entire panel can be removed from the rest of the printer.

  • Using a Phillips #2 screwdriver, remove the motor from the panel by removing the two, 1", Phillips, PH#2 screws.

  • Replace the motor and reassemble the printer following instructions in reverse order.

Add Comment

Finish Line

bbaustin

Member since: 10/12/2011

199 Reputation

6 Guides authored

Team

Cal Poly, Team 17-18, Regan Fall 2011 Member of Cal Poly, Team 17-18, Regan Fall 2011

CPSU-REGAN-F11S17G18

4 Members

6 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 8

Past 30 Days: 36

All Time: 3,484