Introduction

To replace USB port, remove battery first and then remove the USB port while connected to a wire.

To remove the wristband of the device, grab the middle loop and pull. Pull the band through as shown in the picture. To remove the wristband of the device, grab the middle loop and pull. Pull the band through as shown in the picture. To remove the wristband of the device, grab the middle loop and pull. Pull the band through as shown in the picture.
  • To remove the wristband of the device, grab the middle loop and pull. Pull the band through as shown in the picture.

Add Comment

Remove all four Hex screws with a Hex 1.5 mm screwdriver. Remove all four Hex screws with a Hex 1.5 mm screwdriver.
  • Remove all four Hex screws with a Hex 1.5 mm screwdriver.

Add Comment

To remove the HDMI screw, open the HDMI door on the side. Remove the screw using a Phillip size 00. To remove the HDMI screw, open the HDMI door on the side. Remove the screw using a Phillip size 00. To remove the HDMI screw, open the HDMI door on the side. Remove the screw using a Phillip size 00.
  • To remove the HDMI screw, open the HDMI door on the side. Remove the screw using a Phillip size 00.

Add Comment

As shown in the picture, use the plastic opening tool on both sides on the device. Pry apart both parts. Do not pry apart the device too hard. There is a wire that attaches the front case with the rear case. Do not pry apart the device too hard. There is a wire that attaches the front case with the rear case.
  • As shown in the picture, use the plastic opening tool on both sides on the device. Pry apart both parts.

  • Do not pry apart the device too hard. There is a wire that attaches the front case with the rear case.

Add Comment

Deck the Halls
With tools and Fix Kits
Pull the wire ribbon out with a pair of tweezers. Pull the wire ribbon out with a pair of tweezers. Pull the wire ribbon out with a pair of tweezers.
  • Pull the wire ribbon out with a pair of tweezers.

Add Comment

To remove the battery housing, you must first use a Phillips size 00 to remove the 4 screws. To remove the battery housing, you must first use a Phillips size 00 to remove the 4 screws.
  • To remove the battery housing, you must first use a Phillips size 00 to remove the 4 screws.

Add Comment

Use the plastic opening tool to pry the battery housing open.
  • Use the plastic opening tool to pry the battery housing open.

Add Comment

After removing the battery housing, take the battery out. After removing the battery housing, take the battery out. After removing the battery housing, take the battery out.
  • After removing the battery housing, take the battery out.

Add Comment

Here highlighted are the two Phillips size 00 and the slots where the wire is held. Here highlighted are the two Phillips size 00 and the slots where the wire is held. Here highlighted are the two Phillips size 00 and the slots where the wire is held.
  • Here highlighted are the two Phillips size 00 and the slots where the wire is held.

Add Comment

Use plastic opening tool to pry the plastic cover as shown Use tweezers to remove the wire out of slots. Use tweezers to remove the wire out of slots.
  • Use plastic opening tool to pry the plastic cover as shown

  • Use tweezers to remove the wire out of slots.

Add Comment

Remove both Phillips size 00 on USB port.
  • Remove both Phillips size 00 on USB port.

Add Comment

Now push USB port inside the case to remove as shown. Now push USB port inside the case to remove as shown.
  • Now push USB port inside the case to remove as shown.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Robert

Member since: 01/21/2015

894 Reputation

8 Guides authored

Team

USF Tampa, Team 9-2, Blackwell Winter 2015 Member of USF Tampa, Team 9-2, Blackwell Winter 2015

USFT-BLACKWELL-W15S9G2

4 Members

8 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 3

All Time: 215