Tools

No tools required.

Parts

No parts required.

Begin removing the 3/16" screws for the device.
  • Begin removing the 3/16" screws for the device.

Add Comment

Turn the device and remove the additional 3/16" screws.
  • Turn the device and remove the additional 3/16" screws.

Add Comment

Turn the device and remove the additional 3/16" screw.
  • Turn the device and remove the additional 3/16" screw.

Add Comment

Take the white cover plate off. Take the white cover plate off. Take the white cover plate off.
  • Take the white cover plate off.

Add Comment

Using the plastic opening tools, pry open the camera from the bottom.
  • Using the plastic opening tools, pry open the camera from the bottom.

  • This may require a moderate use of force because of the sealing glue.

Add Comment

Deck the Halls
With tools and Fix Kits
Gently pull the connector away from the motherboard.
  • Gently pull the connector away from the motherboard.

Help! I can't get this connector back in place! How did you do it?

Thanks!

rotraut geringer - Reply

Got it finally - and it's working again, I can't believe it! Thank you so much for the instructions!!!!

rotraut geringer - Reply

Unscrew the motherboard's screws. There are 4 3/32" screws and 3 5/32" screws.
  • Unscrew the motherboard's screws. There are 4 3/32" screws and 3 5/32" screws.

Add Comment

Unscrew the lens' screws. There are 1 black 4/32" screw, 3 3/16" black screws, and 2 white 5/32" screws.
  • Unscrew the lens' screws. There are 1 black 4/32" screw, 3 3/16" black screws, and 2 white 5/32" screws.

This seems to be wrong. Only 2 screws connect the lens to the camera body - if you unscrew the others, you open up the lens and there is no need to do so.

NOVOMOTION J. H. - Reply

Pull these connectors away from motherboard.
  • Pull these connectors away from motherboard.

Add Comment

Lift the motherboard and lens out of the case.
  • Lift the motherboard and lens out of the case.

Add Comment

Remove all the screws circled. There is 1 1/8" screw by the flash, 1 9/32" screw that holds the flash button, 2 5/32" screw that is on the grey frame for the flash, and 2 5/32" screws that holds the cable frames on the top left.
  • Remove all the screws circled. There is 1 1/8" screw by the flash, 1 9/32" screw that holds the flash button, 2 5/32" screw that is on the grey frame for the flash, and 2 5/32" screws that holds the cable frames on the top left.

It is not really necessary to remove the whole flash group in order to get to the capture button - you only need to unscrew the lower part (1 screw) and then you can remove the black parts (not fully, but far enough) to uncover the capture button.

NOVOMOTION J. H. - Reply

Unscrew the 3 5/32" screws that cover the battery plate.
  • Unscrew the 3 5/32" screws that cover the battery plate.

Add Comment

The black plates on the other side can be removed after these screws.
  • The black plates on the other side can be removed after these screws.

Add Comment

Pull the flash and battery case out of the device.
  • Pull the flash and battery case out of the device.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

13 other people completed this guide.

Richard Hicks

Member since: 01/13/2015

1,213 Reputation

4 Guides authored

Team

USF Tampa, Team 1-3, Sullivan Winter 2015 Member of USF Tampa, Team 1-3, Sullivan Winter 2015

USFT-SULLIVAN-W15S1G3

3 Members

4 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 19

All Time: 516