Introduction

This guide will demonstrate how to install the USB Ports on your camera.

Parts

No parts required.

Image 1/1: The door will automatically swing open after you let it go.
  • Move the switch on the battery door to the Open position.

  • The door will automatically swing open after you let it go.

Add Comment

Image 1/2: Keep your finger clear of the battery when it pops out. Image 2/2: Keep your finger clear of the battery when it pops out.
  • Push the small gray tab on the top right corner to the left. The battery will pop out slightly.

  • Keep your finger clear of the battery when it pops out.

Add Comment

Image 1/1: The memory card will pop out slightly.
  • Push the memory card in and let go.

  • The memory card will pop out slightly.

  • Pull out the memory card.

Add Comment

Image 1/2: The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm). Image 2/2: The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).
  • Unscrew the small screws on the sides of the camera.

  • The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

Add Comment

Image 1/2: The bottom will fall off. Image 2/2: The bottom will fall off.
  • Unscrew the three small screws on the bottom(#00P, 3.3mm).

  • The bottom will fall off.

Add Comment

Image 1/3: Gently lift up the back cover with your hand from the bottom to the top. Image 2/3: Gently lift up the back cover with your hand from the bottom to the top. Image 3/3: Gently lift up the back cover with your hand from the bottom to the top.
  • Lift up the bottom back cover by prying the bottom edge with the spudger.

  • Gently lift up the back cover with your hand from the bottom to the top.

Add Comment

Image 1/3: The ribbon cables should easily come out of the ZIF connectors. Image 2/3: The ribbon cables should easily come out of the ZIF connectors. Image 3/3: The ribbon cables should easily come out of the ZIF connectors.
  • Lift the tabs on the ZIF connectors.

  • The ribbon cables should easily come out of the ZIF connectors.

Add Comment

Image 1/2: Be careful not to damage the cylindrical capacitor on the circuit board under the top cover. Image 2/2: Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.
  • Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover.

  • Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.

Add Comment

Image 1/1:
  • Remove the small screw in the hole towards the top of the camera(#00P, 5.4mm).

Add Comment

Image 1/2: Using your fingers, gently wiggle and pull off the back motherboard. Image 2/2: You will hear a click when you lift it up.
  • Use the spudger to lift up the back logic board.

  • Using your fingers, gently wiggle and pull off the back motherboard.

  • You will hear a click when you lift it up.

Add Comment

Image 1/1:
  • Remove the small screw holding down the lower motherboard(#00P, 3.2mm).

Add Comment

Image 1/3: Gently lift the lower tab from the main body by prying it with your finger. Image 2/3: Gently pull off the plastic motherboard housing sideways. Image 3/3: Gently pull off the plastic motherboard housing sideways.
  • Use the spudger to lift the upper tab from the main housing.

  • Gently lift the lower tab from the main body by prying it with your finger.

  • Gently pull off the plastic motherboard housing sideways.

Add Comment

Image 1/3: Once you lift the tabs the ribbons should fall right out and the front motherboard should be free. Image 2/3: Once you lift the tabs the ribbons should fall right out and the front motherboard should be free. Image 3/3: Once you lift the tabs the ribbons should fall right out and the front motherboard should be free.
  • Gently lift the tabs on the ZIF connectors connecting the lens to the front motherboard.

  • Once you lift the tabs the ribbons should fall right out and the front motherboard should be free.

Add Comment

Image 1/2: Image 2/2:
  • The USB port is hardwired into this motherboard.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Karissa

Member since: 04/13/2012

29 Reputation

8 Guides authored

Team

Cal Poly, Team 6-23, Amido Spring 2012 Member of Cal Poly, Team 6-23, Amido Spring 2012

CPSU-AMIDO-S12S6G23

4 Members

10 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 1

All Time: 571