Opening a bObi Robotic Vacuum

You're viewing a previously published version of this guide. View latest version

Jan 29, 2015 - 05:17:43

Jan 29, 2015 - 05:17:43 Jan 29, 2015 - 05:17:36 Nov 06, 2014 - 10:45:33 Oct 15, 2014 - 04:39:48 Oct 15, 2014 - 11:26:38 Oct 15, 2014 - 11:15:57 Oct 15, 2014 - 11:15:50 Oct 15, 2014 - 11:13:29 Oct 15, 2014 - 10:21:07 Oct 14, 2014 - 05:17:15 Oct 14, 2014 - 05:16:34 Oct 02, 2014 - 01:23:24 Oct 02, 2014 - 01:23:06 Oct 02, 2014 - 01:19:13 Oct 02, 2014 - 01:18:54 Oct 02, 2014 - 01:16:42 Oct 02, 2014 - 01:11:19 Oct 02, 2014 - 01:11:19 Oct 02, 2014 - 01:11:00 Oct 02, 2014 - 10:55:20 Oct 02, 2014 - 10:54:56 Oct 02, 2014 - 10:53:10 Oct 02, 2014 - 10:42:45 Oct 02, 2014 - 10:39:31 Sep 25, 2014 - 02:31:44 Sep 25, 2014 - 02:18:16 Sep 25, 2014 - 02:17:17 Sep 25, 2014 - 02:14:08 Sep 25, 2014 - 02:13:10 Sep 25, 2014 - 12:06:59 Sep 25, 2014 - 12:04:44 Sep 25, 2014 - 12:04:44 Sep 25, 2014 - 12:03:03 Sep 25, 2014 - 12:03:03 Sep 25, 2014 - 11:56:12 Sep 25, 2014 - 11:56:12 Sep 25, 2014 - 11:53:45

Newer

Introduction

A guide to opening up bObsweep and accessing internal parts such as: main circuit board, ground sensors, wall sensors, side brush motor, UV lamp, power switch, touch sensors, and wheels.

To reassemble bObi, refer to the closing guide. Closing bObi's Cover Post-Repair

What you need

Step 1 Top Cover

Opening a bObi Robotic Vacuum, Top Cover: step 1, image 1 of 2

Opening a bObi Robotic Vacuum, Top Cover: step 1, image 2 of 2

Remove bObi’s front wheel to access one of the screws holding bObi together.
Make sure the wheel is turned closer to bObi's front touch sensors. Use your screwdriver for leverage, and the wheel will pop up and out.
Uninstall the larger screw that sits deeper in the wheel compartment.

Step 2

Opening a bObi Robotic Vacuum: step 2, image 3 of 3

Remove bObi's dustbin.
Uninstall the 2 screws close to the bin and 2 smaller screws above her main brushes.

Step 3

Opening a bObi Robotic Vacuum: step 3, image 3 of 3

Lift the brush holder. To detach completely, unplug it from bObi.
Remove the two screws on the dustbin contact point holder inside bObi.
There are 4 screws beneath the main brushes. Uninstall these, and open bObi up to expose her main circuit board.