Introduction

Use this guide to replace the speaker assembly on your Nexus 5.

  • Use a plastic opening tool to free the clips on the top and each side of the back cover.

  • The bottom is secured with some adhesive foam. You should be able to finally free the back cover using an opening pick.

  • It's best to avoid prying around the SIM card slot, as the plastic here is very thin and likely to break from prying.

Wireless QI and NFC.

Once I have put everything together with the new battery in place, I have as last replaced the plastic back cover, snapping all the clips back around the edges of the phone. Alas, I was quick to realise the QI Wireless charging has ceased to work.

I almost blamed the battery, or worse, me.

QUICK TIP: there is actually another clip in the middle of the plastic back cover - just press with your thumb just above the 'S' in NEXUS emblem and, voila! Snaps back in.

Wireless charge and NFC - works, once again.

cwioro - Reply

you just saved me like 30 bucks. thank you so much.

Robert Nolan -

+ 1, had the same issue and pressing just near the S fixed it! Thanks a lot!

nicco82 -

Just a me too, I had to press above the S and it was quite a snap

Erik Karlin -

There seems to be two contacts that snap into place. One is in line with the led pretty much in the middle of the phone and the second one in line with the camera lens on the opposite side to the lens. The middle one for me snapped pretty lightly, but the side one required a bit more pressure. After that the nfc started working again. Thanks for posting this!

Dennis Millner -

Is it hard to remove the battery door? Worried I might damage it.

Ash - Reply

When I openend the back cover I damaged two clips. One about 2.5cm (1 inch) below the volume controls and one on the other side about same height. The cover fits good without those two but on one side there is a small gap where the clip broke. But I have a hard cover protector on my phone so it's not that bad.

simonlwheeler - Reply

The case around the sim slot is pretty thin and easy to break, best to avoid using the pry tool at this point.

Aled Morris - Reply

Excellent tip, should be included in the main guide.

fprades - Reply

Hey Author, i need to ur expert advice...i replaced my nexus 5's back cover. since the new one did not have the vibrators battery i had to take it from the old one and connect it to the new one...on removing i noticed that it was stuck to the cover by a glue

Question: what glue to use to hold the battery to the cover?

suwaid akbar - Reply

The case around the volume control is also pretty thin.... I broke mine prying so avoid the pry there too.

Also my back had glue at the bottom and I haven't seen mentioned

kornerson - Reply

Remove the four Phillips #00 screws that secure the speaker assembly.
  • Remove the four Phillips #00 screws that secure the speaker assembly.

Add Comment

Use a plastic opening tool to gently pry the speaker assembly out of the phone.
  • Use a plastic opening tool to gently pry the speaker assembly out of the phone.

Do not place your plastic pry tool where shown on the picture. There is a ribbon cable which is easily damaged. Go around the exposed sides instead.

Benjamin Hollway - Reply

Conclusion

To reassemble your device, follow these instructions in reverse order.

16 other people completed this guide.

Chris Willis

Member since: 10/03/2014

1,295 Reputation

6 Guides authored

Team

USF Tampa, Team 13-4, Staggers Fall 2014 Member of USF Tampa, Team 13-4, Staggers Fall 2014

USFT-STAGGERS-F14S13G4

3 Members

6 Guides authored

One Comment

Fantastic! My speaker assembly from iFixit arrived today, and about 20 minutes later I'd just saved myself the $600 dolalrs of buying a new phone. Great site, thanks guys!

Charles Comenos - Reply

Add Comment

View Statistics:

Past 24 Hours: 15

Past 7 Days: 58

Past 30 Days: 237

All Time: 19,317