Turn the Neo3DO face down so that the logo is facing toward you. Insert the plastic opening tool between the metal frame and the plastic back panel, as shown. Insert the plastic opening tool between the metal frame and the plastic back panel, as shown.
  • Turn the Neo3DO face down so that the logo is facing toward you.

  • Insert the plastic opening tool between the metal frame and the plastic back panel, as shown.

Add Comment

Gently pry the back panel upwards. Ensure the tool does not slip into the device and damage the internals.
  • Gently pry the back panel upwards.

  • Ensure the tool does not slip into the device and damage the internals.

Add Comment

Once the back panel has been pried away from the bottom and sides of the Neo3DO, lift the back panel up and away from the tablet. Once the back panel has been pried away from the bottom and sides of the Neo3DO, lift the back panel up and away from the tablet.
  • Once the back panel has been pried away from the bottom and sides of the Neo3DO, lift the back panel up and away from the tablet.

Add Comment

When replacing the back panel, place the top edge of the back panel against the top edge of the Neo3DO, as shown.
  • When replacing the back panel, place the top edge of the back panel against the top edge of the Neo3DO, as shown.

  • The top edge of the device is the edge closest to the camera. The top of the back panel is the side with the hole for the camera.

Add Comment

Remove all the tape attached to the motherboard. Remove all the tape attached to the motherboard. Remove all the tape attached to the motherboard.
  • Remove all the tape attached to the motherboard.

Add Comment

Deck the Halls
With tools and Fix Kits
Pull out the black tabs using the plastic spudger. All sockets that require the same step are marked in the first photo. All sockets that require the same step are marked in the first photo.
  • Pull out the black tabs using the plastic spudger.

  • All sockets that require the same step are marked in the first photo.

Add Comment

Remove the wire belt from the socket. Remove the wire belt from the socket.
  • Remove the wire belt from the socket.

Add Comment

Lift the black tab and then remove the wire belt. Lift the black tab and then remove the wire belt. Lift the black tab and then remove the wire belt.
  • Lift the black tab and then remove the wire belt.

Add Comment

Lift the black tab and then remove the wire belt. Lift the black tab and then remove the wire belt. Lift the black tab and then remove the wire belt.
  • Lift the black tab and then remove the wire belt.

Add Comment

Grip the side of the tab and pull upwards to remove it from the socket. All sockets that require the same step are marked in the first photo. Gripping the wire belt and pulling upwards may cause damage, be sure to avoid it.
  • Grip the side of the tab and pull upwards to remove it from the socket.

  • All sockets that require the same step are marked in the first photo.

  • Gripping the wire belt and pulling upwards may cause damage, be sure to avoid it.

Add Comment

Remove the screws using the J0 head screwdriver. All screws that require the same step are marked in the first photo.
  • Remove the screws using the J0 head screwdriver.

  • All screws that require the same step are marked in the first photo.

Add Comment

Grip the active(red) wire and apply the soldering tool until the solder is soft enough for the wire to be removed. Repeat the same process to remove the neutral(black) wire. All wires that require the same steps are marked in the first photo.
  • Grip the active(red) wire and apply the soldering tool until the solder is soft enough for the wire to be removed.

  • Repeat the same process to remove the neutral(black) wire.

  • All wires that require the same steps are marked in the first photo.

  • The soldering tool is extremely hot, use with caution.

Add Comment

Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up. Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up. Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up.
  • Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up.

Add Comment

Remove the plug from the motherboard socket. Remove the plug from the motherboard socket.
  • Remove the plug from the motherboard socket.

Add Comment

Grip the wire and apply the soldering tool until the solder is soft enough for the wire to be removed. The soldering tool is extremely hot, use with caution. The soldering tool is extremely hot, use with caution.
  • Grip the wire and apply the soldering tool until the solder is soft enough for the wire to be removed.

  • The soldering tool is extremely hot, use with caution.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Daniel Evans

Member since: 09/26/2016

431 Reputation

4 Guides authored

Team

USF Tampa, Team 14-3, Eyestone Fall 2016 Member of USF Tampa, Team 14-3, Eyestone Fall 2016

USFT-EYESTONE-F16S14G3

3 Members

6 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 1

Past 30 Days: 3

All Time: 63