Introduction

This guide will show you how to remove the hard drive cable from your laptop.

With the case closed, place the Unibody top-side down on a flat surface.
  • With the case closed, place the Unibody top-side down on a flat surface.

  • Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.

Add Comment

The access door should now be raised enough to lift it up and out of the Unibody.
  • The access door should now be raised enough to lift it up and out of the Unibody.

Add Comment

Be sure the access door release latch is vertical before proceeding.
  • Be sure the access door release latch is vertical before proceeding.

  • Grab the white plastic tab and pull the battery up and out of the Unibody.

Great tutorial ! great step !

Leo Etcheverry - Reply

Remove the following eight screws securing the lower case to the chassis:
  • Remove the following eight screws securing the lower case to the chassis:

    • One 3 mm Phillips screw.

    • Three 13.5 mm Phillips screws.

    • Four 3.5 mm Phillips screws.

On my model, it seemed the top-left was 3.5mm and the bottom 4 were 3 mm.

Jim - Reply

Make sure you have a good quality Phillips screwdriver. Mine had removable tips and had a small play at the connection. As a result I didn't have a good feel and damaged my screws (those securing the fan and the top left in step 23). Game over for me installing new thermal paste...

Be very carefull with your screws! Especially those on the inside.

Nickolas Michelinakis - Reply

Using both hands, lift and remove the lower case off the upper case.
  • Using both hands, lift and remove the lower case off the upper case.

Add Comment

Using the flat end of a spudger, pry the subwoofer connector straight up off the logic board.
  • Using the flat end of a spudger, pry the subwoofer connector straight up off the logic board.

Me, too, broke the subwoofer connector from the motherboard. I'd suggest removing the padding first so that you can see what kind of connector it is, then pry it loose (insert spudger where the cables enter the connector).

petterwolff - Reply

DO NOT REMOVE THE SUBWOOFER CONNECTION. Step 6 IS NOT NESCESSARY.

You can complete this guide without doing step 6 just BE CAREFUL as you already should be.

kenneth rhem - Reply

The subwoofer cable is NOT removable on some models, attempting to remove it, brakes it off the circuit board and them you are @@%#$$, like me. Thanks iFixit. Also it is not necessary to remove it to replace the optical drive.

todd - Reply

Oops, I followed Step-6 and my subwoofer connector came off from the motherboard!!! Please suggest me what needs to be done now?

Srinivasan - Reply

Happened the same to me ... step 6 is a @%#$$. You should put now a way to repair the damage done. I just have four small tin marks on the board ...

stratorick - Reply

Happened the same problem to me ... step 6 is a @%#$$**%%#. You should put now a way to repair the damage done. I just have four small tin marks on the board ... and looking to sky for help

Badruddin Hisbani - Reply

Disconnect the camera cable by pulling the male end straight away from its socket.
  • Disconnect the camera cable by pulling the male end straight away from its socket.

Add Comment

Use a spudger to pry the optical drive connector straight up off the logic board.
  • Use a spudger to pry the optical drive connector straight up off the logic board.

Add Comment

Remove the two Phillips screws securing the subwoofer to the upper case.
  • Remove the two Phillips screws securing the subwoofer to the upper case.

  • The longer of the two screws is on the right.

Add Comment

The subwoofer is still connected to the right speaker, so don't completely remove it just yet.
  • The subwoofer is still connected to the right speaker, so don't completely remove it just yet.

  • Lift the subwoofer off the optical drive, and set it above the computer.

Add Comment

Remove the two Phillips screws securing the camera cable bracket to the upper case.
  • Remove the two Phillips screws securing the camera cable bracket to the upper case.

  • The leftmost screw may remain captive in the camera cable.

This step is not necessary. Drive can be released without removing the screws.

mcbohdo - Reply

Remove the three 2.5 mm Phillips screws securing the optical drive to the upper case.
  • Remove the three 2.5 mm Phillips screws securing the optical drive to the upper case.

Add Comment

Lift the optical drive from its right edge and pull it out of the computer.
  • Lift the optical drive from its right edge and pull it out of the computer.

  • The hard drive cable may become disconnected from the logic board when removing the optical drive. Ensure it is connected during reassembly.

Add Comment

Remove the single Phillips screw securing the hard drive bracket to the upper case.
  • Remove the single Phillips screw securing the hard drive bracket to the upper case.

  • This screw is captive in the hard drive bracket.

Add Comment

Lift the hard drive by its plastic pull tab and remove the freed hard drive bracket.
  • Lift the hard drive by its plastic pull tab and remove the freed hard drive bracket.

Add Comment

Lift the hard drive out of its supports and disconnect the SATA cable by pulling the connector straight away from the hard drive.
  • Lift the hard drive out of its supports and disconnect the SATA cable by pulling the connector straight away from the hard drive.

Add Comment

Remove the four 10.3 mm Phillips screws securing the mid wall to the upper case.
  • Remove the four 10.3 mm Phillips screws securing the mid wall to the upper case.

Add Comment

Lift the mid wall out of the upper case.
  • Lift the mid wall out of the upper case.

Add Comment

Use a spudger to pry the hard drive cable connector straight up off the logic board.
  • Use a spudger to pry the hard drive cable connector straight up off the logic board.

Add Comment

Peel the hard drive cable from the adhesive securing it to the upper case, and maneuver the plastic retaining block out of the upper case. During reassembly, be sure the two pins on top of the plastic retaining block mate to the holes on the underside of the midwall.
  • Peel the hard drive cable from the adhesive securing it to the upper case, and maneuver the plastic retaining block out of the upper case.

  • During reassembly, be sure the two pins on top of the plastic retaining block mate to the holes on the underside of the midwall.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

18 other people completed this guide.

Team

iFixit Member of iFixit

Community

127 Members

6,377 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 10

Past 7 Days: 81

Past 30 Days: 353

All Time: 34,521