Introduction

Use this guide to replace the system board

Tools

No tools required.

Parts

No parts required.

Look at the back of the tablet and locate the speakers on top of the rear cover.
  • Look at the back of the tablet and locate the speakers on top of the rear cover.

  • There is a smaller indentation in the plastic cover that runs across the top of the device.

  • Wedge the plastic opening tool, under the middle of the cover as shown, then push up and the cover will pop off.

I just want to find out if my sd card is stuck inside how do I remove it without damaging the tablet.

Tom Mukotora - Reply

Remove SD card if present. Remove the following two screws:
  • Remove SD card if present.

  • Remove the following two screws:

    • M3.0 x 3.0 mm #00 phillips screws (black)

Add Comment

Pry open cover using a plastic opening tool. Leave plastic opening tool in place to maintain the separation. It may take a little force to separate from the front face of the device
  • Pry open cover using a plastic opening tool.

    • Leave plastic opening tool in place to maintain the separation.

    • It may take a little force to separate from the front face of the device

  • Slide the plastic opening tool to one corner.

    • Place another plastic opening tool into the gap and slide it to the opposite corner.

  • Pull the rear cover up and back to separate it from front face of the device.

Add Comment

Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing. Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing.
  • Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing.

Add Comment

Black Friday
Broken doesn't stand a chance.
Remove the following seven screws: M3.0 x 3.0 mm #00 phillips screws (black).
  • Remove the following seven screws:

    • M3.0 x 3.0 mm #00 phillips screws (black).

  • The top right corner screw is underneath a yellow ribbon. Lift the ribbon up without disconnecting it and unscrew the screw.

Add Comment

Now you can take the battery out in order to either replace it or continue disassembling the device. Now you can take the battery out in order to either replace it or continue disassembling the device.
  • Now you can take the battery out in order to either replace it or continue disassembling the device.

Fantastic advice. After being told by Lenovo I needed to shell out £110 for a new mobo when it just had a charging socket issue I took it upon myself to see if I could fix it. This website helped take it apart and I found that the charging socket is just a micro daughter-board.

If you have a problem with charging then go to http://www.replacebase.co.uk and search for Lenovo A2109A. They have all the parts.

I replaced the daughter board and battery for about £10 incl del. Parts arrived yesterday and I have fitted. Works a treat. Not sure what amazes me the most, the low cost of the parts and excellent service by replacebase or the fact Lenovo tried to rip me off.

These instructions are spot on.

Well done

Goon'

Andy Blunn - Reply

Remove the following five screws: Two M 3.0 x 3.0 mm #00 phillips screws (black) Three M 5.3 x 1.75 mm #00 phillips screws (silver)
  • Remove the following five screws:

    • Two M 3.0 x 3.0 mm #00 phillips screws (black)

    • Three M 5.3 x 1.75 mm #00 phillips screws (silver)

You can skip step 8 and step 10, leave these connectors in place (just remove the speaker connector in step 9) lift board enough to remove I/O board and leave most connectors in place.

green1eng - Reply

There are four connections that you must disconnect in order to remove the system board Use tweezers to flip up the small black plastic locks on all four connections Carefully remove each of the exposed ribbons
  • There are four connections that you must disconnect in order to remove the system board

  • Use tweezers to flip up the small black plastic locks on all four connections

    • Carefully remove each of the exposed ribbons

Add Comment

Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing. Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing.
  • Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing.

Add Comment

Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector. Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector.
  • Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector.

Add Comment

Disconnect the HDMI connection with the system board Use a plastic opening tool to pry up the system board, and you will hear a pop as it comes free Slide out the system board from its housing tab on the upper right corner
  • Disconnect the HDMI connection with the system board

    • Use a plastic opening tool to pry up the system board, and you will hear a pop as it comes free

  • Slide out the system board from its housing tab on the upper right corner

  • Pull the board slowly away from the tab, and it will pop out.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 other people completed this guide.

Kyle

Member since: 04/22/2014

518 Reputation

2 Guides authored

Team

Cal Poly, Team 7-19, Regan Spring 2014 Member of Cal Poly, Team 7-19, Regan Spring 2014

CPSU-REGAN-S14S7G19

4 Members

7 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 13

All Time: 1,142