Kindle Fire Ambient Light Sensor Replacement

Remove the ambient light sensor in an Amazon Kindle Fire.

Use this guide to help you replace the ambient light sensor in the Amazon Kindle Fire.

Edit Step 1 Back Case  ¶ 

Image #1

Edit Step 1 Back Case  ¶ 

  • Wedge a plastic opening tool into the lower right corner of the Kindle Fire.

  • Pry the case apart and run the plastic opening tool along the perimeter of the Kindle Fire to release the clips securing the case halves to each other.

  • If you are having extreme difficulty inserting the plastic opening tool, carefully use a metal spudger to undo the first clip, then switch back to the opening tool to avoid scratching your case.

    • It is helpful to pry the bottom of the Kindle Fire away (and out from the side) from the top part. Exerting too much force attempting to split the two without pulling away can cause the tabs on the inside to crack.

Edit Step 2  ¶ 

Image #1

Edit Step 2  ¶ 

  • Once you have freed all the plastic clips, pull the back case off the Kindle Fire.

Edit Step 3 Battery  ¶ 

Image #1

Edit Step 3 Battery  ¶ 

  • Fit the tip of the plastic opening tool between the right battery cell and the Kindle Fire's frame.

  • Lever the battery up and work the plastic opening tool down along its edge to release the glue securing it to the frame.

Edit Step 4  ¶ 

Image #1

Edit Step 4  ¶ 

  • Repeat the process from the previous step to free the left battery cell.

Edit Step 5  ¶ 

Image #1

Edit Step 5  ¶ 

  • Lift the back of the battery up to relieve any tension in the battery connector and simultaneously use a spudger to push the battery connector out of its socket.

  • Pull the battery out of the Kindle Fire.

Edit Step 6 Speaker Assembly  ¶ 

Image #1

Edit Step 6 Speaker Assembly  ¶ 

  • Peel the tape on the upper-left IC that is securing the speaker cable.

  • Use the flat end of a spudger to push the speaker connector out of its socket.

  • Deroute the speaker cable.

Edit Step 7  ¶ 

Image #1

Edit Step 7  ¶ 

  • Remove the two 3.3 mm Phillips #00 screws securing the speakers to the Kindle Fire.

  • Lift the speakers out of the Kindle Fire.

Edit Step 8 Motherboard  ¶ 

Image #1

Edit Step 8 Motherboard  ¶ 

  • Remove the two 2.3 mm Phillips #00 screws from the touchscreen controller.

  • Use a plastic opening tool to release the touchscreen controller connector.

  • Gently remove the touchscreen controller by lifting it up and to the right.

    • Be careful not to rip the ribbon cable in doing so.

Edit Step 9  ¶ 

Image #1

Edit Step 9  ¶ 

  • Use a plastic opening tool to flip open the power button ZIF connector.

    • This connector will not be removed until the motherboard is free.

  • Flip open the ambient light sensor ZIF socket with a plastic opening tool.

  • Use a pair of tweezers to pull the blue tab on the ambient light sensor cable to remove it from its socket.

Edit Step 10  ¶ 

Image #1

Edit Step 10  ¶ 

  • Use a plastic opening tool to lift up and disconnect the display data cable.

  • Lift up on the antenna connector with a plastic opening tool to disconnect it.

  • De-route the antenna cable.

Edit Step 11  ¶ 

Image #1

Edit Step 11  ¶ 

  • Remove the six 2.6 mm Phillips #00 screws securing the motherboard to the frame.

Edit Step 12  ¶ 

Image #1

Edit Step 12  ¶ 

  • Use a plastic opening tool to gently lever up the bottom side of the motherboard to free from the adhesive on its underside.

  • Lever the top side of the motherboard up with a plastic opening tool until it comes free.

  • Lift the motherboard out of the Kindle Fire, making sure that the power button cable from step 8 comes free from its connector.

Edit Step 13 Power Button Board  ¶ 

Image #1

Edit Step 13 Power Button Board  ¶ 

  • Remove the 2.5 mm Phillips #00 scew securing the power button board to the Kindle Fire.

  • Lift the power button board out of the Kindle Fire.

Edit Step 14 Frame Loosening  ¶ 

Image #1

Edit Step 14 Frame Loosening  ¶ 

  • Use the flat end of a spudger to peel the ambient light sensor cable off of the frame.

    • You will need to peel up the silver tape in the cable's lower right bend. The silver tape under the lower left bend of the cable does not need to come up with it.

Edit Step 15  ¶ 

Image #1

Edit Step 15  ¶ 

  • Use the flat end of a spudger to peel up the silver tape securing the antenna cable.

  • Remove the five 3.6 mm Phillips #00 screws securing the frame and ambient light sensor.

Edit Step 16 Ambient Light Sensor  ¶ 

Image #1

Edit Step 16 Ambient Light Sensor  ¶ 

  • Slide the ambient light sensor out from under the frame and remove it from the Kindle Fire.

    • If the ambient light sensor will not easily come out, slightly lift the frame with a plastic opening tool to allow it to come free.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the Kindle Fire device page.

Required Tools

Spudger

$2.95 · 50+ In stock

Phillips #00 Screwdriver

$5.95 · 50+ In stock

Tweezers

$4.95 · 50+ In stock

Tweezers

$4.95 · 50+ In stock

Tweezers

$4.95 · 50+ In stock

Recommended Tools

54 Bit Driver Kit

$29.95 · 50+ In stock

Pro Magnetic Project Mat

$19.95 · 50+ In stock

Pro Tech Screwdriver Set

$59.95 · 50+ In stock

Anti-Static Project Tray

$4.95 · 50+ In stock

Popular Device Products

Comments Comments are onturn off

Make sure to mark what ZIF connector goes where, they are not interchangeable even though a first glance the appear to be the same size

David Alvarez, · Reply

It took about 2 hours, but that is, mainly, because reconnecting the ZIF connectors can be overly tedios.

David Alvarez, · Reply

Apparently not all Kindle Fires have the ambient light sensor; This connector is not present on mine.

diprosew, · Reply

I cannot get the zif connectors to go back in ..what can i do...been trying for hours to get them back in...im talking bout the white flip pieces that lock in film..some one please help me with this!!

bearangel246, · Reply

Be very careful when disconnecting the antenna, and be sure to note how the cable is routed into the little socket on the motherboard. The reconnecting of the antenna cable into its motherboard port can be tricky and will require patience, persistence and perhaps a magnifier and tweezers.

Jeff Jones, · Reply

note that the image still displays the speakers that were supposed to be removed in an earlier step

diprosew, · Reply

Followed the steps but once reassembled the screen comes on but doesn't respond to touch. It was working fine even with broken glass screen. Any suggestions?

John Moore, · Reply

Mine is doing the same thing! What did you do to fix it?

Tara,

View Statistics:

Past 24 Hours: 3

Past 7 Days: 13

Past 30 Days: 54

All Time: 5,913