Introduction

Since the vintage hand-held 'Bricks/Tetris' gaming consoles were manufactured mostly in the 1990's, their internal components are most likely worn by now. The silicone rubber membrane key switches under the buttons will periodically need to be cleaned and/or replaced. Cleaning under sticking buttons in itself is not a challenging task. The issue arises when one or more solder joints break after disassembling the device in order to access the silicone rubber membrane. Avoiding the failure of solder joints with one of these consoles is almost impossible due to age and the shortness of the wires inside. Disassembling the cover by itself will frequently result in a breakage of the solder joints connecting the main board wires to the batteries. Therefore this guide instructs the owner of one of these vintage hand-held gaming consoles to restore the game's functionality after discovering the game will not power on.

Use a Phillips 1 screwdriver to unfasten the four screws from the back of the case. Remove the battery cover to expose the two remaining screws that hold the case together.
  • Use a Phillips 1 screwdriver to unfasten the four screws from the back of the case.

  • Remove the battery cover to expose the two remaining screws that hold the case together.

Add Comment

Unfasten the last two screws, and open the case. Unfasten the last two screws, and open the case.
  • Unfasten the last two screws, and open the case.

Add Comment

Identify the wire(s) which have been disconnected, and identify their original location.
  • Identify the wire(s) which have been disconnected, and identify their original location.

  • If two or more wires were disconnected, use two AA batteries to verify the correct wiring. The game’s starting melody will be audible if the wiring is correct.

Add Comment

Using the same Phillips 1 screwdriver, unfasten the two smaller screws holding the controller board to the case . Remember the position of the screws; take a picture if need be.
  • Using the same Phillips 1 screwdriver, unfasten the two smaller screws holding the controller board to the case .

  • Remember the position of the screws; take a picture if need be.

Add Comment

Verify that the detached wire(s) reach the intended destination. Use a blade or wire stripper to strip 0.5 cm of insulation off the end of the wire(s) to be soldered. Sharp tool!
  • Verify that the detached wire(s) reach the intended destination.

  • Use a blade or wire stripper to strip 0.5 cm of insulation off the end of the wire(s) to be soldered.

  • Sharp tool!

Add Comment

Re-solder the disconnected wire to the proper joint. Lightly tug on the newly soldered wire to confirm a reliable solder joint. Refer to How To Solder and Desolder Connections if needed.
  • Re-solder the disconnected wire to the proper joint.

  • Lightly tug on the newly soldered wire to confirm a reliable solder joint.

  • Refer to How To Solder and Desolder Connections if needed.

  • Hot iron! Noxious fumes!

Add Comment

Assembly is the reverse of disassembly.
  • Assembly is the reverse of disassembly.

  • Install two AA batteries, and verify audibility of the game prior to reassembly.

Add Comment

Conclusion

Although newly manufactured hand-held Brick gaming consoles are plentiful to purchase online, the owner of an earlier generation hand-held Brick gaming console will most likely want to keep the original ones they bought. There is no telling if/when these devices will become a collector's item, but history has shown that not all types and models of these hand-held Brick games are being manufactured. Some models were manufactured for a very limited period of time. The owners of those rare Brick games will eventually want to fix theirs. Not much else can go wrong with these Brick games as long as the owners protect the LCD screens from damage.

Nardeen Hamid

Member since: 02/10/2016

101 Reputation

1 Guide authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 7

Past 30 Days: 41

All Time: 552