Introduction

This is a guide to removing the camera's logic board.

Image 1/2: One screw is on upper right corner of the back panel. Image 2/2: The other four screws are on the bottom of the camera.
  • Unscrew five Phillips screws using a #0 Phillips screwdriver.

  • One screw is on upper right corner of the back panel.

  • The other four screws are on the bottom of the camera.

Add Comment

Image 1/1: Remove the memory card from the slot.
  • Open memory card cover by moving the slide switch toward the top end of of the camera.

  • Remove the memory card from the slot.

Add Comment

Image 1/1: This may require gentle rocking of the case to free it.
  • Remove the rear cover from the rest of the camera.

  • This may require gentle rocking of the case to free it.

Add Comment

Image 1/2: Image 2/2:
  • Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

Add Comment

Image 1/1: The cover may require gentle rocking to remove.
  • Free the front cover from the rest of the camera.

  • The cover may require gentle rocking to remove.

Add Comment

Image 1/1:
  • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

Add Comment

Image 1/1: Be careful not pull the LCD too far because of the ribbon cable connection.
  • Gently separate the top of LCD from the rest of the camera using your thumb.

  • Be careful not pull the LCD too far because of the ribbon cable connection.

  • Place the Spudger in the hole of the electrical ribbon.

  • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

  • The LCD will still be connected to the rest of the camera

Add Comment

Image 1/2: Free the bottom panel and attached ribbon from the rest of the camera. Image 2/2: Be careful not to damage the ribbon.
  • Unscrew single Phillips screw with a #0 Phillips screwdriver.

  • Free the bottom panel and attached ribbon from the rest of the camera.

  • Be careful not to damage the ribbon.

Add Comment

Image 1/1: Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.
  • Turn over the camera.

  • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

  • The plastic will still be connected on the left side.

Add Comment

Image 1/1: Lift the ribbon gate using the Spudger.
  • Place the Spudger between the orange ribbon and the black ribbon gate.

  • Lift the ribbon gate using the Spudger.

Add Comment

Image 1/1: Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.
  • Place the Spludger in the corner of the ribbon above the hole.

  • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

Add Comment

Image 1/1: Be careful not to damage the ribbon.
  • Free this ribbon and the bottom panel from the rest of the camera.

  • Be careful not to damage the ribbon.

Add Comment

Image 1/1: Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.
  • Turn the camera over so you can see the LCD.

  • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

Add Comment

Image 1/1:
  • Lift the blue ribbon gate using the Spudger.

Add Comment

Image 1/1: Move the Spudger away from the gate to fully remove ribbon.
  • Insert the Spudger into the hole of the ribbon.

  • Move the Spudger away from the gate to fully remove ribbon.

  • Be careful not to damage the ribbon.

Add Comment

Image 1/1:
  • Lift the LCD away from the rest of the camera.

Add Comment

Image 1/2: Be careful not to damage the two clips. Image 2/2: Be careful not to damage the two clips.
  • Lift off the capture button by wiggling it back and forth while pulling upward.

  • Be careful not to damage the two clips.

Add Comment

Image 1/2: Gently pull out the ribbon cables from the gates using the Spudger. Image 2/2: Gently pull out the ribbon cables from the gates using the Spudger.
  • Flip open the four ribbon gates using the Spudger.

  • Gently pull out the ribbon cables from the gates using the Spudger.

Add Comment

Image 1/1:
  • Unscrew the four Phillips screws using a #0 Phillips screwdriver.

Add Comment

Image 1/2: Be careful not to pull too hard and damage the white ribbon cable. Image 2/2: Place the Spudger so that it is between the logic board, the white ribbon cable, and the rest of the camera.
  • Gently lift the the logic board.

  • Be careful not to pull too hard and damage the white ribbon cable.

  • Place the Spudger so that it is between the logic board, the white ribbon cable, and the rest of the camera.

  • Remove the white ribbon cable by pulling the Spudger away from the camera, keeping it parallel to the logic board.

Add Comment

Image 1/1: Pull the two plugs (white and green) out to the right from the logic board using the tweezers.
  • Lay the logic board back down so that it is resting on the body of the camera.

  • Pull the two plugs (white and green) out to the right from the logic board using the tweezers.

Add Comment

Image 1/2: Please do not perform this step if you are not comfortable or have previous experience with soldering.  Doing so, could cause severe damage to your camera. Image 2/2: Desolder the two soldered ribbon cables attached to the logic board.
  • We're now ready to begin the desoldering process. You'll need a soldering iron, solder, and desoldering wick. You should be able to find these items at a Radio Shack if you don't already have them.

  • Please do not perform this step if you are not comfortable or have previous experience with soldering. Doing so, could cause severe damage to your camera.

  • Desolder the two soldered ribbon cables attached to the logic board.

Add Comment

Image 1/1:
  • Free the logic board from the rest of the camera.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Nathan Balcom

Member since: 01/21/2010

81 Reputation

8 Guides authored

Team

Cal Poly, Team 16-28, Maness Winter 2010 Member of Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 Members

9 Guides authored

One Comment

How brilliant! Great pictures! But where did you buy the new logic board?

Rosario - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 2

All Time: 2,595