Introduction

The speakers are necessary for audio communication while using the video phone's video call function. The speakers are not necessary for calls that do not involve video.

Press upwards with your index finger on the 4P4C connector  as shown in the image. Pull the connector gently out of its socket.
  • Press upwards with your index finger on the 4P4C connector as shown in the image.

  • Pull the connector gently out of its socket.

Add Comment

Flip the main body of the video phone so that the bottom is facing up.
  • Flip the main body of the video phone so that the bottom is facing up.

  • Use the Phillips #0 Screwdriver to remove the four Phillips head screws (6 mm) highlighted by the red circles.

Add Comment

Lift the back case upwards to expose the inside components. Red rectangles indicate the three ribbon cables.
  • Lift the back case upwards to expose the inside components.

  • Red rectangles indicate the three ribbon cables.

  • The orange square indicates the blade connector.

Add Comment

Disconnect the three ribbon cables  from their insulation-displacement connectors by flipping up the black plastic clip. Gently pull the ribbon cables out of their insulation-displacement connectors. Gently pull the ribbon cables out of their insulation-displacement connectors.
  • Disconnect the three ribbon cables from their insulation-displacement connectors by flipping up the black plastic clip.

  • Gently pull the ribbon cables out of their insulation-displacement connectors.

Add Comment

Disconnect the blade connector from the blade receptacle by gripping the exposed area of the blade connector. Gently pull the blade connector out of the blade receptacle.
  • Disconnect the blade connector from the blade receptacle by gripping the exposed area of the blade connector.

  • Gently pull the blade connector out of the blade receptacle.

Add Comment

Deck the Halls
With tools and Fix Kits
Gently lift up the lower case to separate it from the top case.
  • Gently lift up the lower case to separate it from the top case.

Add Comment

Use the Phillips #0 Screwdriver to remove the four Phillips head screws (6 mm) highlighted by the red circles.
  • Use the Phillips #0 Screwdriver to remove the four Phillips head screws (6 mm) highlighted by the red circles.

Add Comment

Gently lift up on the  upper case to separate it from the keypad/speaker panel. The ribbon cable is highlighted by the red rectangle.
  • Gently lift up on the upper case to separate it from the keypad/speaker panel.

    • The ribbon cable is highlighted by the red rectangle.

    • The 2-pin JST connectors are highlighted by the orange squares.

Add Comment

Disconnect the ribbon cable from its insulation-displacement connector by flipping up the black plastic clip. Gently pull the ribbon cable out of its insulation-displacement connector. Gently pull the ribbon cable out of its insulation-displacement connector.
  • Disconnect the ribbon cable from its insulation-displacement connector by flipping up the black plastic clip.

  • Gently pull the ribbon cable out of its insulation-displacement connector.

Add Comment

Disconnect the two white 2-pin JST connectors from the keypad/speaker circuit board by tugging gently until they release. Disconnect the two white 2-pin JST connectors from the keypad/speaker circuit board by tugging gently until they release. Disconnect the two white 2-pin JST connectors from the keypad/speaker circuit board by tugging gently until they release.
  • Disconnect the two white 2-pin JST connectors from the keypad/speaker circuit board by tugging gently until they release.

Third photo in this collection may be unnecessary.

Cason Fluharty - Reply

The red markers indicate the four plastic clips arranged around the base of each speaker housing. Use a plastic spudger to push in the four plastic clips.
  • The red markers indicate the four plastic clips arranged around the base of each speaker housing.

  • Use a plastic spudger to push in the four plastic clips.

Add Comment

Once both speakers have been unclipped, gently pull the  wire through the housing . Once both speakers have been unclipped, gently pull the  wire through the housing .
  • Once both speakers have been unclipped, gently pull the wire through the housing .

First photo here may be unnecessary.

Cason Fluharty - Reply

Use the Phillips #0 Screwdriver to remove the two Phillips head screws (6 mm) Gently lift up the black cover to expose the now freed speaker. Gently lift up the black cover to expose the now freed speaker.
  • Use the Phillips #0 Screwdriver to remove the two Phillips head screws (6 mm)

  • Gently lift up the black cover to expose the now freed speaker.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Itze Kenney

Member since: 02/14/2017

1,045 Reputation

9 Guides authored

Team

USF Tampa, Team 20-4, Remmell Spring 2017 Member of USF Tampa, Team 20-4, Remmell Spring 2017

USFT-REMMELL-S17S20G4

4 Members

10 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 3

All Time: 74