SR8855 Disassembly
4. Disassembly & Assembly
4-1. Precautions & Main Tools
- Be sure to turn off the Power Switch before disassembling or as sembling the unit.
- Be sure to use the rated parts when replacing electronic compon ents (check the Model Name; the Rated Voltage/Current; the operating temperature; etc)
- When repairing the unit; be sure to keep water away from the ha rness and assemble it firm.
- The assemble wire harness connectors should not be slipped out when pulling out with moderate force.
- When repairing the unit; be sure to remove dust or foreign subs tances completely from the connector housing; the wire connection parts; the terminal contacts; etc.
It is to prevent any fire possibilities such as tracking; short etc.
- Check if there is any trace of water penetrated to the electric al components If so; replace the components or seal up the area with insulation tapes.
- Check the assembled status of the components after repairing th e unit Keep the assembled status the same as the previous status.
- Check its using environments (The Robot Cleaner is for domestic & indoor use:) When it is used for other purposes; it may cause major damages to the unit (operation error, broken down; etc)
- Do not Use Attics, Underground Floor; Warehouse; Industrial B uilding, Watery Area; Fire hazard area; Narrow & High Laying Areas s uch as Table; other not residential area.
- Do not have the customers repair the unit by themselves.
- Tools for disassembly and assembly Flat Head Screwdriver; Phi Ilips Screwdriver .
4-2. Main Body Disassembly & Assembly
| Category | Description | Visual Description |
|---|---|---|
| (1) Turn off main power | Flip over the Main Body and turn off the Power Switch (OFF) . | |
| (2) ASSY CASE BASKET (Dust Bin) | Press the Eject Button and separate the Dust Bin by pulling it out. Be sure that the dust in the Ceuton Dust Bin not get spilled out. | Eject Button |
| (3) ASSY DRUM BRUSH (Power Brush) | Press the locking tap (2ea) with fingers and separate the Lift up the Power Brush from the Main Body and separate it. | Power Brush |
Table Caption: This table provides step-by-step instructions for disassembling a device, detailing how to turn off the main power, remove the dust bin, and detach the power brush. It also includes visual cues to aid in identification.
| Category | Description | Visual Description |
|---|---|---|
| (4) ASSY BRUSH CORNER L/R (Side Rotating Brush) | Remove the screw with the Phillips Screwdriver and separate the left Side Rotating Brush (Separate the right one in the same way) When the rotating brush is bent or dirty; hold it with a Cautlon lukewarm steam towel and clean it. | |
| (5) ASSY BATTERY (Battery) | Remove the screws (2ea) with the Phillips Screwdriver and separate the Battery Cover. Lift up the ASSY BATTERY and disassemble the Connector | Battery Cover |
| (6) ASSY BODY BUMPER | Bemove the screws (2ea) and separate the CAP-SCREW |
Table Caption: This table outlines the steps for disassembling and cleaning specific components of a device, including corner brushes, the battery assembly, and the body bumper. It specifies the tools required, such as a Phillips screwdriver, and provides brief visual cues for certain parts.
| Category | Description | Visual Description |
|---|---|---|
| (6) ASSY BODY BUMPER | Remove the ASSY BODY BUMPER by pulling it out Separate the Connector from the Main Body . | |
| (7) COVER SIDE L/R | Unlock the tab and separate the COVER SIDE L (Separate the other side in the same way) . | |
| (8) PANEL CONTROL | Remove the screws (2ea) fastened to the PANNEL CONTROL. Press the two locking tabs and remove the PANEL CONTROL by flipping it over backwards. | COVER SIDE L PANEL CONTROL |
Table Caption: This table outlines disassembly steps for automotive components, providing a description of the action and a visual reference for specific parts. It details how to remove the ASSY BODY BUMPER, COVER SIDE L/R, and PANEL CONTROL.
| Category | Description | Visual Description |
|---|---|---|
| (9) BODY MID | Remove the screws (6ea) and separate the BODY MID by lifting it up. | |
| (10) ASSY PBA MAIN | Remove the PBA-DISPLAY by lifting it up Remove all the connectors from the PBA MAIN and the screws (4ea) And then; separate the PBA MAIN. | PBA DISPLAY |
| (11) PBA TOUCH (Touch Sensor) | Remove the HOLDER DISPLAY and separate the PBA TOUCH assembled under the INLAY DISPLAY (only for VC-RA8* Series) | DISPLAY COVER |
**Table Caption: This table outlines a disassembling procedure, detailing steps for removing components like the BODY MID, ASSY PBA MAIN, and PBA TOUCH, and provides brief visual descriptions for some
