Student-Contributed Wiki
An awesome team of students from our education program made this wiki.
NutriBullet Will Not Turn On
The blender will not respond and does not show any signs of powering up.
The blender is not plugged into a wall source
Check to make sure the cord is properly plugged into the wall outlet. The wall outlet must provide a minimum of 120 volts. Any voltage less than 120 volts will not turn the NutriBullet on.
The blender has a faulty cord
Inspect to see if the cord is torn or wire is exposed. If it is, then follow these guidelines to replace the cord.
The cup is missing a tab
Check the cup you're using to see if a tab has broken off. If it has, the blender will not power up.
Electrical Problems
If the Bullet has been subject to extended, non-pulsed use, two electrical components could have failed which would cause the Bullet to not spin. In either case, at the time of failure there probably was a smell of hot metal or electrical components. The two components are: a heat sensor which fails permanently if the motor coils heat above 105deg Celsius; or the carbon brushes which conduct electricity to the commutator segment of the motor. Diagnosis will require a disassembly of the unit, and require an electric multimeter as a tool to assess conductivity.
NutriBullet Leaks
The device is blending food, but there are evident leaks and spillage.
Extractor blade is not screwed onto the cup lid tightly
Check to see that the extractor blade is screwed onto the cup lid properly by using the ridges on the cup as a guide. If it still does not screw on properly, order a new one here.
Rubber seal on extractor blade is torn or ripped
There is a rubber seal called the gasket on the underside of the extractor blade. This helps to secure it to the cup and prevent leakage. If it is torn or ripped, follow this guide to replace it.
Cup is not properly secured into the powerbase
Ensure the cup is tightly secured and locked into the high-torque power base. There are three slits on the powerbase that match the three lips located on the side of the cup.
There are cracks on the interior or exterior parts of NutriBullet
Detach the cup from the high-torque power base and inspect all parts of NutriBullet powerbase to ensure no cracks are found. If there is a crack, the NutriBullet could expose wires or fast moving components. If a crack is found on the base, replace it. If a crack is found on the cup or lid, '''purchase a new one.'''
Blades Do Not Turn
Although the device is plugged in and on, the blades refuse to turn.
The blender has been in use for a prolong period of time
The makers of the NutriBullet recommend that you do NOT blend for more than 1 minute. Prolonged use of the machine can cause the motors to wear out quickly, which can affect the blades.
Motor refuses to turn even though cord is plugged into a wall source
If the blades do not turn and you notice a burning smell, unplug the power base and let it cool for an hour. The powerbase will reset once the unit is unplugged.
Activators refuse to operate even though cup is tightly secured to the powerbase
In order for the NutriBullet to blend, there are special white activators on the top of the power base which begins the blending process. If the blades fail to turn when the cup is in the powerbase, the activators could be stuck. Follow these instructions to replace the activators.
Blades Refuses to Cut or Blend Food
The blades will not blend food items fully or takes a long time to do so.
There is food stuck in between the blades
First, unplug the NutriBullet from the outlet and remove the extractor blade to clear any obstruction or build up of food. Be careful not to cut or injure yourself in the process.
The cup is too full to blend or cut food
Depending on which cup you are using (30 oz Short Cup or 45 oz Oversized Cup), there is a max line which determines how much food or liquid is recommended. Surpassing the max line could prevent the blades from cutting or blending food.
The blades are spinning, but refuses to blend or cut food to its entirety
Blades may be dull and new replacement blades can be ordered here.
Blender Stops Suddenly During Use
When you are using the NutriBullet, the machine stops suddenly during use.
Blender becomes unplugged during use
Ensure that the cord is still plugged in the wall and has not come out during its use.
The blender has wires and other components exposed
Loose wires and other internal components from the device may become exposed during the course of use. If so, please refer to the replacement guide on how to replace the outside casing, which makes it easier to work on internal parts of the device.
Team
Cal Poly, Team 19-8, Maness Winter 2015 Member of Cal Poly, Team 19-8, Maness Winter 2015
CPSU-MANESS-W15S19G8
4 Members
10 Guides authored
140 Comments
I would like to point out there is a flaw concerning the base attachment. The flaw being the direction the base rotates in will cause the cup to become loose. This in turn causes the unit to leak. Refitting with left hand threaded cups and blade assemblies would alleviate this problem.
henrysisson - Reply
I have just purchased a 900W machine and it leaks like a sieve!! there is nothing broken or torn the cup just seams to come undone whilst the machine is running, this is hopeless
Helen -
This happened to me as well. I ordered a replacement jar after a tab broke off the original and it would no longer operate. The replacement was garbage. The base would not easily seat on the new jar but after carefully screwing it on, I thought I had it covered. Nope. I turned it on and the d##m thing loosened and there was a flood of smoothie everywhere. The flood ruined the motor - this was as I said - a flood. Now I have a drawer full of cups and blades with no base. Should I discard them all and look for something else?
jhjones713 -
I have this same issue and came here to find an answer. It didn’t do it originally, but now every time I try to use it, it loosens and risks a leak. I daren’t use it anymore. It’s a shame because it was a great blender before this started. Also, it does it with both attachments even though one is barely used, and the cup is fine, so it must be the actual unit that is the problem somehow.
Lottie Bennett -
My Nutribullet cup with blades attached will not drop down into the blending mechanism. It stops about an inch above, so doesn't get close the the white activator switches. What is it hitting? How can I fix this?
astarrfire - Reply
I have this same problem, have you found a resolution?
babehre -
I have the same problem today, have you find any answer?
Elizabeth Rauda -
I called them they helped me rested the white strips on the inside of the unit. Call customer service they can help you.
Amy Zangerle -
Did you find a solution? I think mines the seal is not right so the cup won’t go on correctly but I cannot figure out how to put the seal incorrectly.
matthewsabear -
I have the same problem
Greg von Buchau -
I am also having this problem, but nothing obviously blocking it...?
sianellingworth - Reply
I am also having this issue. The cups seems to be down all the way and it turns on but the base grinds down the rubber tips on the bottom of the blade base. I'm on my second one and it's doing it again! So annoying. Need to find a blender that works
Ann Marie - Reply
I am having a problem with the bottom inserting completely into the housing. it is not even reaching the white activators and is sitting about 1/4 in above them. I cannot see any problems so What Is Up?? I tried both blade assemblies and neither one will fully insert into the base. Suggestions? Is there a part that is missing that I have not noticed? I cannot find any photos of the top of the motor housing..
I used it yesterday and it worked fine.
amydelachica - Reply
I have this problem too, did you find a fix?
Pete -
I am having this problem too
scseley -
Hi not sure if you got this fixed but I had same problem and realise the lip ring was stuck inside the base unit (I had popped it in there to store it safely). It looks like it's part of the base so easy to miss. Just lifted it out with a fork. I sent a message with a pic to the Nutirbullet Facebook Page and they helpful sent me a few pics back showing what it should look like and how to fix it.
kirstenpegller -
Wow--Kristenpegller was right--I feel stupid--
fcw -
If you rotate the cup one or two positions to connect it to the base and lock it in it will go on, at least that worked for me.
Nancy d -
I am unable to screw cup off base of nutribullet. What do I do?
mena rechichi - Reply
I had this same problem. They helped me reset my little white strips on the inside of the unit. Fixed it right away. Call customer service they will help you and it's a fast phone call.
Amy Zangerle - Reply
does water leeking from the cup not tightened properley damage the motor
crystalteacher - Reply
I was making my husband a smoothie and I made sure the lid was on well and it leaked everywhere and then the cup was stuck on the base and I couldn't get it off. Now the machine on pulses when being used. I just bought this and love it and I cant afford to buy another one and I don't think the reciept was saved.
kittycatcrisper - Reply
Same problem. Mine was a gift to me and I'm very disappointed. It leaks all over my counter. I used it twice and I may toss it. I wish I could send this crappy thing back. It scares me!
precision Brown -
Ours leaked on the first use, took it back and got another one. It lasted about 1 week and started leaking as well, I contacted the company and they sent me a new blade. Put it on and it continues to leak. I have just contacted the company again. It's an absolute mess to try and use the way it leaks out into the base. Sorry I bought this.
pjent1 -
It is very difficult to push the container down to engage the system. Very stiff. Seems almost stuck. I need to use a lot of force not every time , but much of the time. I am concerned that I will break the small tips on the container that activate the process. Help or suggestions?
Bob
Bob Leslie - Reply
Sorry no help or suggestions mine leaked the first time I used it so once more and it may be history. I hate it!
precision Brown -
Personally my ninja was a gift and the very bottom leaks all over. I'd never buy one of these for anyone ever!
precision Brown - Reply
Ninja was given to me as a gift. I thought I'd be impressed but I'd never buy anyone this thing ever! I'm afraid to use it. I'd love to send it back!!
precision Brown - Reply
if the cup doesn't fit down into the base correctly just short of reaching the tabs you're ream lid may have fell down into the base you can ease it out with a fork
gibbonst48 - Reply
I am the same, poor set up, when I make a smoothie the base unwinds and smoothie goes everywhere
The base needs to lock into place then there wouldnt be a problem, I may look into slotting the base and gluing a block for it to slot into,
If the base doesnt go down , I found the motor and the tabs on the base were hitting, simple fix, just moved the motor around a fraction and down it went.
I am surprised NUTRIBULLET has not made comment as to the comments on here, or made suggestions on fixes. mitchfj12@hotmail.com
does worry me about liquid going down around the motor
other than that yes its a great item
mitchfj12 - Reply
I find it is extremely difficult to even get the blade on the jar - does not align well with threads and always wants to screw on crooked. I have to redo it so many times, I usually just abandon my intent for a healthy smoothie and go for something else. Very disappointed in Ninja, wish I had selected the NutriBullet.
Sharon Kerr - Reply
The bullet stopped working while in use
Esther BROOKS - Reply
My bullet suddenly stopped working
Esther BROOKS - Reply
My magic bullet was working just fine last night and now it locks just fine, it pushes down just fine but it doesn't start at all. Makes no noise, nothing happens. I plugged it into every outlet in the house and still nothing happens. So I know that too low of power isn't the problem, it's just not turning on what so ever. Mine was also a gift so there's no receipt whatsoever.... Any help?
Taeya Xak - Reply
I have the same problem. did you ever find the solution?
Thanks Sabrina
Sabrina Stevens -
My nutribullet 1200 series won't turn on. Despite running through these checks. The blue light on/off button keeps flashing.
Julie Jackson - Reply
where am I going to be the magic bullet repair
Or
there a service center here in the philippines?
florentinokarenjoy24 - Reply
Mine won't stop hearing things. I've unplugged it I've tried the button a hundred times it won't stop. I've only used it maybe 25 times.
Andrew Mcdonald - Reply
I have the original magic bullet and it still works great. Most of the parts that came with it are still in their plastic. One issue that I have been having is that when I put the blender (anything that has a blade) on the unit I have to hold down the blender and when I first got the unit I could just turn to the right when blending and it would stay running until I turned to the left to remove the blender. Any suggestions how to fix this.
Thanks
pcmacbob - Reply
My Baby Bullet leaked through the base and now the base is gunky. It's usable but i have to carefully lift the top container out slowly because the base continues to spin and spin for a while. I believe it's because the leaks that have occurred have made everything very gunky and sticky. I could have sworn one of the times it leaked, it's as if the thing loosened ITSELF during use...weird. How do i clean that gunk out. I've tried dried brushes etc but this stuff is the consistency of mushed raisin.
geni499 - Reply
I have only had mine for about 2 weeks. Do I have to hold down on it to make it go? Once, I let my hands off and it continued to blend but now it won't do that. Do you have any ideas?
Mary T. Camp -
I try to use it with hot coffee and it just goes everywhere what am I doing wrong?
nannyleeann - Reply
You are not supposed to put hot liquids in there as the cup will pressurize and can explode when opened.
Jackson Halvorson -
the bit just inside the unit that connects to the cup when you screw it down and start it has disappeared !! its just a naked screen thats left , what could have happened?
lynnhunt - Reply
I don't use the bullet often but I have notice that the motor seems to not engage with the rotating device that spins the blades. This results in a very noise machine, smoke/sparks and black soot from the vent.
Does anyone else experience this or is this how the bullet rolls.
Sean's Mojo - Reply
The blender works but after 15 seconds it starts to be loud and burn. Anything I can do and is that dangerous ?
robbieh - Reply
My cup is stuck in the machine and won't come out. Has anyone else had this?
Ellie campbell - Reply
Yes! Mine too. Were you able to get it off the machine? If so please share how! Right now my entire machine is sitting in my refrigerator full of yogurt and fruit!
tsgieger -
Help! I know the answer is too easy, but my nutribullet is ready to go but it simply won't start. I have checked everything I can think of and have been unable to get it to start. Any good ideas?
Candace
Candace Brunson - Reply
I have a problem where my NutriBullet will not turn off when when I removed the cup. Upon plugging it in alone, the blades begin spinning, even without the cup in. The press-down tabs are NOT engaged. I’m confused as to what to do.
Mekkel Richards - Reply
I am facing the same issue too!! Any solution?
Srihari Raghavan -
Having a hard time atching and activating the blender it doesn't match up with the base
HARVEY FORBES - Reply
I buy my nutibullet at 9/15 17… just use it a couple of times… and now it does not work anymore… what do I do now.?
tavarez.marlene - Reply
I buy my nutri nullet at 9/15/17,and just use it a couple of times what do I do now.?
tavarez.marlene - Reply
My Nutribullet will not power on. I checked the outlet, the cord and the tabs. Nothing wrong there. What else should I check??
Sally Donnelly - Reply
Could anyone help me please. I have the Magic Bullet. When I put the ingredients into the cup and place it on the base unit, I usually just pulse it for a minute or so. I’ve just put it on and somehow I seem to have locked the cup to the base unit. I had to turn it off at the wall but cannot get the cup off. There seems to be three little grooves on the base unit (which I never noticed before) and I can’t see any way of releasing it. Unfortunately ''''cannot find the book that came with it. Sorry to be a pain if it is something so simple a child could do it!
Celia Goode - Reply
Can’t remove top off cup after it finished operating. Tried putting under hot water for short time. Any suggestions?
Joanna Sobolewski -
I just had the same issue. With nothing to lose, I used a small standard screwdriver and placed it between the cup and the Magic Bullet rim and forced it to unlock. What I noticed, was that one of the three tabs on the cup had broken. I transferred everything into a new cup and this time I was able to get it to work.
Anne Born -
I need help!!! Any suggestions on removing lid after blending smoothie?
My one and only problem with my NutriBullet Rx is the size of the lid containing the extractor blade. It is very wide. I have struggled several times with opening it after blending my smoothies.
Today I again struggled with removing the top after making my smoothie. In fact, I STILL CANNOT OPEN IT!
It is difficult to get a good grip on the large lid. I wish the size of the lid was not so wide. My hands are larger than most women’s hands, so I wonder how someone who is petite or of less strength is able to unscrew the lid so they can eat their smoothie. Dang! I wanted to drink my smoothie! :(
Karen Mahlen - Reply
I have had this problem: the surfaces are really slick, making it difficult to get a good grip. My solution is to put a large, thick rubber band around the blade housing, giving me a better grip. This has worked for me.
kruth -
Hi,
My new Nutribullet RX won’t stop unless I switch off the power button.
I tried making soup but it leaked through the base so I cleaned the base and let it dry out.
I tried making soup again and it just kept spinning at full speed and wouldn’t stop - it nearly boiled over. I let it cool down and tried making a smoothie - same thing - it kept spinning at full speed, the green light went off but is just kept spinning.
When I put the jug on it starts spinning immediately at full speed, no delay.
It worked find the first 4 or 5 times.
Thanks
Joanne
Joanne Pattinson - Reply
My cup would not push down enough to turn to lock in place. Called nutribullet. Told to take tooth brush to top white 3 places where it locks and scrub. Took a couple of tries and now works again. Hope his helps.
deeannet - Reply
I just purchase my nutri bullets 600 series but it doesn't work. Is there any service center in the Philippines.. I bought it in united Arabs of Emirates. Last August 06,2018.. Email liza 0038@gmail.com.
step aero tan - Reply
Need advice as to why the cup pops off during blending from the activators after 5 secs which means we need to hold in place to complete the process.
Activators all working well so unsure of the cause??
Linda Stewart - Reply
I found out today if whats in the cup isn’t heavy enough it will not blend either so try adding a little of your treat into the cup and try again. I also reset my white tabs inside the unit.
johnson_enjoli - Reply
Hi my nutribullet has cross thread and now and I can’t detach it
nicky.mullings - Reply
The cup is secure but won’t go down inside the cup stops up above the rubber blades before it seats will not connect?
jhowlett1 - Reply
Having same issue
tishagene -
Wow i was gonna buy one, guess i not now. Looked up for a friends that stopped working
A. Sirname - Reply
We have used our nutribullet just now and it leaked when attached to the base and switched on so we removed it from the base and gave it a wipe down but when we tried removing the lid from the cup it wouldn't come unloose and still hasn't, it has been passed around through four sets of hands and none of us are able to open it, who else has had this issue and what do you do?
Tillea Harvey - Reply
My 9000 didn’t like ice in my smoothy. Turned off and is now dead. Brand new. My old one lasted 5 years. So annoyed.
ainsley - Reply
I have same problem today. Any solutions ?
Hazelnut - Reply
My nutribullet is not turning on at all, it is pretty new. But as the others mentioned the leaking probably got into the motor. I have opened it and I am allowing it drain the liquid to see if that will fix the issue
Shikara Williams - Reply
My Nutribullet stopped working out of nowhere! How do I fix it? Or can I even fix it?
Kaily Cravens - Reply
My nutribullet leaks black ink like liquid from the main component each time it is used and the noise is now louder than normal - don't want to use it as expect it to explode (that loud!) - why is there black liquid from the machine? Have taken photos to show to help but cant upload here.
J TS - Reply
My magic bullet is stuck spinning unless I unplug it! What do I do?
bcressobrn - Reply
el botón parpadea dañen azul y no funciona
Roberto De Anda - Reply
Hello friends, the blue button started to flash and does not work
Roberto De Anda - Reply
I leave my blender plugged in all the time. When I go to use it, it won’t true non and I have to unplug it and plug it back in before it will work. Why does this do this?
mysinhiscross - Reply
How many years does a Nutribullet RX supposedly last . mine is 6 yrs. Old and spins for 2 seconds thats it . Anybody else have this problem
Kelly Anderson - Reply
My NutriBullet would not start. I used the troubleshooting guide and all the explanations were useless. I took a really good look at the machine and the problem was that one of the buttons along the rim that the cup tabs are supposed depress was stuck. I gently moistened the tab with water and carefully ran a thin knife along the edges, then sprayed a little WD-40 on it. I pressed the button again and it started to give. Eventually with a few more presses it came free and the button started working normally. My NutriBullet works fine now :-)
Jeanne Whitehouse - Reply
My Nutribullet Balance when plugged in the light blinks and goes out. No power after. Anyone has a fix
DWIGHT WILLIAMS - Reply
After I turn my Nutribullet off sometimes is keeps running, and unplugging it while it’s still on could be dangerous any ideas on how to fix this?
Rachel Oyeyemi - Reply
My cup won't go down to begin working my 3 prongs are fine cup just won't go down
tishagene - Reply
I can’t get the cup to connect to the power base. I have tried halving the quantity of ingredients but it will not push down so as to engaged the cogs to the power base
trish Dobson - Reply
My nutribullet will not start, its plugged into to working outlet; The only thing I noticed is the clear circular disk with pie shaped slices in base is cracked-not sure if this would be the issue?
Angela Fazio - Reply
I bought my nutribullet a few months ago. I used it for the first time today. It worked for less than 30 seconds then stopped. I haven't been able to get it started since.
djf5130 - Reply
Nutri bullet serial number: 232I01031902310 purchased 6 months ago,not turning on, in spite good power cord etc.
jagan_kanala - Reply
For our NutriBullet, it does engage and work, however I need to keep constant downward pressure on the cup to keep it going. Otherwise it stops. Anyone have any ideas? Thanks!
Jeffrey Bunce - Reply
My Nutribullet Pro worked fine last night and today nothing happens when I attach the cup. It doesn’t do anything at all - no noise, no hum, nothing. The cord is in good shape, there is power to the outlet, the cup has all its tabs, the cup sets properly into the base, it’s clean and there are no leaks. The cup locks properly into the power base. It’s only 3 months old.
sheammt - Reply
Whenever I blend something that looks like motor oil or some sort of thick and dark lubricant is apparent on the metal ring around the rubber part on the backside of the blades. I think this is because something is missing or a nut or bolt is loose and it sprays the stuff around then it spins. Does anyone know a fix to this?
Jackson Halvorson - Reply
My blender is spewing contents out of the base , out of the cup I have bought new seals but this didn’t fix the problem
This the second email with no advice
johncleary7 - Reply
slicer blade is stuck and cannot be removed. please advise.
slicer problem - Reply
This is such a poorly engineered piece of junk, in my view. I don’t understand how these folks stay in business!!!
slicer problem - Reply
My nutri bullet won’t stay attached it starts to blend then makes a noise then the machine spits the whole cup out it has all its tabs and it’s had a good clean??
Natalie - Reply
If the motors of the nutribullet is worn out because of the prolongation of use, will it still work after few hours of letting it cool? Thank you for answering my query.
nnesjoarlyo_27 - Reply
I am getting error message on app , nutrilite sensor not stable .Any advice ?
nick comzee - Reply
Mine doesn’t turn on, no blue light. Yesterday, it leaked very little, I dry everything that I could see, today it doesn’t turn on. Help please :)
fnejat - Reply
Hi. Just blended my protein shake, but cup won’t depress, turn and detach.
mopptopp - Reply
My nutribullet only works on the impulsion pulse bottom and not on low or high!
Lucia Franco - Reply
The cup became loose while blending, now it won’t turn on at all.
virginia Taylor - Reply
Hi, i need some help. PLugged food in the cub with blade base on, push down and turn to get the blender going, and the motor starts sounding like it’s going into overdrive, like there is no resistance, and a burning smell occurs. I tried ice after to see what the blade itself was doing when turned om, and the blade spins sporadically, with the motor again whirring at a million miles an hour, with a very distinctive sound? What can I do to fix this? Any help much appreciated
tobster18 - Reply
My RX ,it was coming smog out of it during blending and I'm afraid to use it again. I just pull the cord to disconnect. Please!! Can I buy only the motor??? And where??
Mrs. Estrada
Nora Estrada - Reply
The rubber seal seal keeps coming off….hard to stretch to put back on….but it should stay on
gwendols22 - Reply
After using the machine, I can’t get the cup out of the base. It won’t budge
Judith - Reply
I have only used my Nutribullet six times and every time I use it the rubber seal falls out and is very hard to get back in.
Linda - Reply
Nutribullet cup and blade stuck in the blend position. Will not come off of base.
Dawn Vargas - Reply
Hello. My nutribullet will not work. The power cord is intact, the fuse is fine, and the activators are also fine (I have taken it apart to check). Any other ideas? One post mentions the heat sensor, how would I check this? Thanks
Gemma Webster - Reply
My NutriBullet won't allow me to unscrew the cup from the blender. How do I get it lose?
Andréa Parker - Reply
my blade has dirty black stuff where it connect to the base. how to fix this? do i have to buy new bled.
SANJAY - Reply
*following. Did you ever find a resolution? The same is happening to me & the motor spins but does not blend causing a very concerning smell when in use.
Mlm -
My Veggie Bullet was given to me it was working fine but now I'm having trouble with the power botton what can I do & how much would it be to have it serviced I don't have the warranty for it
Rosa Rodriguez - Reply
Hola, una pregunta, mi licuadora es RX y no se activa, prende el foco azul y el rojo de enmedio parpadea, que puedo haces…
Gracias de antemano, saludos.
hac.plv - Reply
Hi, i have this nutri bullet in fact I have two and the part that the motor is screwed on to is broken at the two places where the screws are holding down the motor. Can anyone tell me where can I purchase this part from?. Thanks. PS. I have a picture of what it is but I cant upload it here. Please send reply to asurujbally@hotmail.com
Akenath Surujbally - Reply
HI .I have this nutribullet and its broken where the motor screws on to the housing at both places. can anyone tell me where can I get this part to buy. How can I post a picture of it? I should also mention that I have two nutribullet and the same thing has happened to both of them. thanks. please send reply to asurujbally@hotmail.com.
Akenath Surujbally - Reply
The base with the cup attached does not drop down to the bottom of the base of the machine. Nothing stuck inside, rotated it several times and several directions, tried the other blade with cup, does the same thing. No drop! HELP!
hrts333 - Reply
SOLUTION FOR CUP AND BLADE NOT DROPPING DOWN ON MOTOR BASE!!! I contacted customer service and they had me send a pic of the motor base and there was a threaded ring in the base that was not supposed to be there. He advised to remove with a spoon. it worked with the spoon edge inserted into one of the threads, gently pulling up and turning the spoon around the circumference of the thread and it came up! Yeah! The threaded ring can be attached to the cup, if you want to drink the smoothie directly from the cup.
hrts333 - Reply
Blender lid does not seal? Product isnt usable.
fungo44 - Reply
Good morning Sirs…the blender doesn't finish the blending cycle…it keeps half powering down and then powering up throughout the blending cycle.
Bindi Shah - Reply
my nutri bullet cup not opening
caracara57 - Reply
kirstenpegller was right. I lifted the lip ring out with a knife and it’s fixed now. Thank you for your help.
sriveraf0616 - Reply
Porque mi nutribullet, se enmojese de la base.
Jose E Cruz - Reply
mix the black fat from the blades into food
bigmarlin1 - Reply
La grasa negra de las cuchillas se menclan con los jugos es peligroso tengan cuidado hay que tener mucha precaución si notan el cambio de color oscuro en tus alimentos, estare esperando una respuesta favorable a mi solicitud
bigmarlin1 - Reply
The light blinks on my Nutribullet nb2-s10 and the blender will not activate. Can it be fixed and What can I do to get it working again?
Mead Ministries - Reply
Cup is stuck shut with liquid in it. How to open?
susanhegg - Reply
Donde puedo comprar este sello lo nesecito
ivelisse garcia - Reply
Se le salió una grasa a la parte externa de las aspas por lavarla de ahí y ahora suena muy fuerte que puedo hacer?
Bere - Reply
My nutribullet high-torque blade is loosened from the tight base. Now it keeps shredding the plastic area around it. How do I fix that?
Nibeditaaa - Reply
I cannot get the blades to rotate by hand - they appear jammed. The unit does not operate despite checking that the 3 actuators are operating normally
Peter Stacey - Reply
I’m with astarrfire, just years later. I’ve purchased this over a year ago, was working fine the first maybe 10 times and then just started doing this. Did anyone figure out if it’s me or the device?
staciteeslink - Reply
Se encienden todas las luces y se me detuvo, ya no funciona
Iris Villalobos - Reply
Hi, my new blade won't turn even though it is securely attached. It won't click to the base. My old blade working out just fine.
I'm using pro 1000w. Please help.
Sabrina S - Reply
The sides, the three parts on the cup that lock it in to the body are stuck after use. One of them has been almost melted down, pushed so hard in that now I can’t twist the cup, so it opens.
Danny Balinski - Reply
Nutribullet unit nbt-15 is not disconnecting from cup and blade . I’m currently holding unit upside down and unscrewing cup . Unit and blade section won’t disconnect from each other. This has happened twice units is only 3 months old.
shawn powell - Reply
The cup doesn't fit properly in the blender, even though it was working perfectly
Juan Garcia - Reply
make sure you put on the lid. the large container will not power on to function without the lid on.
pmsunda - Reply
My nutribullet power light will not come on; this unit has been pampered. The cord is good the unit is in perfect condition. Any suggestions?
Randy Tate - Reply
I can’t remove the cup from the blade unit? Any ideas? It’s stuck and immovable
Cheryl D'Cruz-Young - Reply
There is a black soot like substance coming from the bottom of the blender and the motor spins but it does not blend. Can this be fixed?
Mlm - Reply