The Xbox 360 is one of the most powerful gaming consoles on the market. I may have the Halo 3 Edition, but the dissasembly for all models is the same.

The disassembly of this console is not easy, but with some patience you can do it.

This Disassembly also works with HDMI models, and Non-HDMI models

Begin by removing the hard drive, (skip this step if your console doesn't have a hard drive)

Press the button on the hard drive, then pull up near the front. Once the front is removed, slide the drive forward and then lift the drive out.

Removing the Face-Plate

Put two fingers into the USB port area, then push down, while pulling the face-plate towards you.

Not so pretty anymore!

Removing The Top Bezel

Make sure the console is standing up. Then look into the grill.

The red circles mark the location of tabs (like this on the other side too). Together there are 6. To pull off the top grill, use a small round object to insert into the holes onto the tab, then pull up on the grill, freeing it partially. You need to do this to all 6 tabs to ensure you don't break them. Then lift the grill up. This process is the same for the top and bottom.

The Tabs Are Circled In Yellow

As you can see, I got lazy and broke two of them. Try not to do the same, yet as long as most of the tabs are there, it should still go back on. So don't sweat it, if you break them.

The Bottom Grill

Flip the console over, and remove the bottom grill the same way you removed the top one.

Once you are done removing the grills, both the top and the bottom should look like this.(3rd Photo)

The Point of No Return

Once you break the Microsoft seal, we can continue. Start by taking multiple flathead screwdriver bits or 4 spudgers (The most common spudger is a black or yellow nylon stick with a metal hook at one end.) and put them in these 4 latches to hold them open.

After all 4 tabs are held open, pull up on the top half of the case. The bits should pop out(don't lose them!). Lift the case up and make sure the tabs don't reconnect.

Lift the half up and then flip the console upright, and make sure that you don't let the tabs close.

Removing the bottom half.

This next step is hard, but I promise that the bottom half comes off.

Using a small flathead screwdriver, pry these tabs apart. It's hard to show how to remove the clips, but you'll see soon enough.

Using a flathead screwdriver, pop out all 7 tabs. It's hard to do this without causing some damage to the casing.

Removing the bottom/right half.

These pictures should explain how it's done.

Once all tabs are free, flip the console back over and lift the bottom half off.

Removing the Top Half

Using a small flathead screwdriver, or a spudger, remove the eject button assembly.

It should come off easily, but some models have adhesive, making the process slightly harder.

Removing the top half.

Flip the console over and remove the 6 T10 Screws. They should each be 2.5" long, if not, you removed the wrong screws.

Then flip the console back over, holding it by both the plastic and the metal.

Now lift the top half off, and Voila! You now have access to the guts.

Removing the DVD Drive.

It is a SATA DVD drive with a proprietary Xbox power connector.

Lift the drive up near the back revealing the connectors.

Pull the drive out of the console. There may be tape on the front of the drive holding it in, remove the tape.

Set the drive aside.

Removing the Fan Shroud.

Using a flathead screwdriver, pry out the tab connecting it to the fans.

Lift the shroud out.

Removing the Fans.

Remove the 3-Pin power connector from the logic board. This is the same connector used in some PC fans.

Using a flathead screwdriver, pry the fans toward you.

Pull the fans toward you, then lift them out of the casing.

Removing the Fans

Here are pictures of the fans and power connector.

Removing the "Ring Of Light"/RF board.

Pop off the plastic LED cover.

Remove these 3 T8 Screws

Pull the board toward you. Than set it aside.

Removing the logic board.

Remove these T10 Screws from the bottom metal casing, there may be more than the number circled, just remove them all.

If they are present, remove these T8 Screws from the bottom metal casing.

Flip the casing over.

With a little persuasion, the logic board should lift out of the casing.

Custom ATi GPU with up to 512MB of GDDR3 VRAM, memory shared with the CPU via Shared Memory Architecture

IBM PowerPC CPU with 3 Cores, each running at 3.20GHz with up to 512 MB of GDDR3 SDRAM, shared with GPU via Shared Memory Architecture

Memory Card Ports

Hard Drive Port

HDMI and Video Ports

Power Port

There's also a bunch of integrated circuits on here. What I've noticed:

Microsoft X02014-007

6 x Samsung K4J52324QC-BC14 512MB GDDR3 SDRAM

Microsoft X0247-012 BGA IC

Numerous x NTD60N02R Power MOSFETs

ADP3188 Synchronous Buck Controller(?? See datasheet)

The Guts!