iPad 2nd and 3rd Gen Home Button Assembly

$12.95

Product code: IF110-009
Apple Part #: 820-2943-A

Click Image To Zoom

 
 
 
 

iPad 2nd and 3rd Gen Home Button Assembly

$12.95

Product code: IF110-009
Apple Part #: 820-2943-A

Product Overview

This part contains the the plastic home button, control board, mounting bracket and spring. It also has adhesive on it so it can be installed.

Compatibility

Identify your iPad

  • All Second Generation iPads
  • All Third Generation iPads

Product Details

$12.95 Black

 
 

Condition:

New

$12.95 White

 
 

Condition:

New

Add to Cart
 

Replacement Guides

iPad 2 CDMA

Difficulty: Very difficult

iPad 2 GSM

Difficulty: Very difficult

iPad 2 Wi-Fi EMC 2415

Difficulty: Very difficult

iPad 2 Wi-Fi EMC 2560

Difficulty: Very difficult

iPad 3 4G

Difficulty: Very difficult

iPad 3 Wi-Fi

Difficulty: Very difficult

 

Compatibility

iPad 2 CDMA
16 GB
32 GB
64 GB
iPad 2 GSM
16 GB
32 GB
64 GB
iPad 2 Wi-Fi EMC 2415
16 GB (EMC 2415)
32 GB
64 GB
iPad 2 Wi-Fi EMC 2560
16 GB (EMC 2560)
iPad 3 4G
16 GB LTE/CDMA (3rd Gen)
16 GB LTE/GSM (3rd Gen)
32 GB LTE/CDMA (3rd Gen)
32 GB LTE/GSM (3rd Gen)
64 GB LTE/CDMA (3rd Gen)
64 GB LTE/GSM (3rd Gen)
iPad 3 Wi-Fi
16 GB Wi-Fi (3rd Gen)
32 GB Wi-Fi (3rd Gen)
64 GB Wi-Fi (3rd Gen)
 

Stories

My Problem

Pushing the home button had no results unless it was pushed very hard

My Fix

The new parts ordered were installed without concern. After cleaning off the glue strips, I temporarily installed the digitizer screen and the home button still did not function as expected. Made some measurements and found that the two pins that are on the charge assy were not contacting the home button control board. The two angled screws from the charge harness were removed. A piece of black tape was used under the charge harness to lift it slightly higher. Parts were reinstalled and it then functioned as expected.

My Advice

Make sure to totally clean off all old glue strips. Also clean off old glue residue the best you can. This good prep will insure good bonding of the digitizer screen to the ipad housing. Also make sure all smudges are cleaned off the LCD screen and inner digitizer screen before final installation. Good luck.. This procedure is very easy if you just take your time.

My Problem

Front glass broken

My Fix

Was ok! The problem has been fixed in around 2 hours

My Advice

Be patient and concentrate!

My Problem

A friend offered me his iPad that had a badly broken screen for free. He knows that I'm pretty handy with woodworking, so he thought I might give a try with electronics. He had covered it with packing tape, and it was still functional, but it would make some errors recognizing touches, swipes, taps, and such. With a free iPad in my hands I figured it was worth investing a little money into it just to have the experience, even if I ended up ruining it.

I have an iPad supplied by my employer, and this was going to be for my wife and kids.

My Fix

I didn't want to buy a new front panel if I ended up destroying the iPad in the dis-assembly process. So I actually removed the broken glass before ordering the new parts. The fact that I am writing this now is proof that the removal went okay (it was a little harder than I expected) and while I had no way to be sure if it was still working, I had not done much visible damage.

The only thing I damaged was the wi-fi/bluetooth antenna, but it looked like it was only damage to the part that holds it in place--I thought it would not impair the function. So I ordered the front panel, and waited for it to arrive. It came faster than expected! (Well played, iFixit. Well played.)

In case you are seeing that I ordered the home button assembly--the button bent a little when I peeled it off the old glass, and probably would have been okay after a touch of flattening. But I tought it might be weakened and, therefore, fail sooner rather than later. I decided to order a new home button assembly just for good measure, because I don't want to have to open up this iPad again.)

When the front panel and home button arrived the assembly on that part was really easy. When I got it back in place enough to test, it turns out that the wi-fi antenna needed some help. It was working, but clearly getting a weak signal (only 1 bar, standing 3 feet away from my Time Machine tells me there was a problem.) So I ordered a new wifi antenna, and my wife and the kids got frustrated that they were going to have to wait for another delivery. But it also came faster then expected! (Bravo, iFixit.)

Putting the wifi antenna in required removing more internal parts, which was a little nerve-wracking, but I got it in, and went to test - Success!!!

My Advice

Wear eye protection when removing broken glass. Covering the whole glass front with tape would probably be a good idea. I had tape on part, but not all, of the screen--it made a noticeable difference.

Take seriously the warnings about the location of the wifi antenna.

The tools that come withe the front panel assembly kit seem like they would have really helped the removal process. I would have been better off ordering the part in advance.