Skip to main content

Fix Your Stuff

Right to Repair

Store

Notice: You are editing a prerequisite guide. Any changes you make will affect all 7 guides that include this step.

English
Japanese

Translating step 2

Step 2
Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame. If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display. Insert an opening pick into the gap.
  • Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame.

  • If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display.

  • Insert an opening pick into the gap.

  • Slide the pick around the sides and bottom of the display to cut the adhesive. Apply more heat as needed.

  • Work carefully—the glass is thin and will crack easily if you try to force it.

  • Separate the top edge last. There are antennas on both sides, so be careful not to damage them. Use more heat or a bit of isopropyl alcohol to help weaken the adhesive.

吸盤またはiSclackをガラスに吸着させ、ガラスと金属フレームとの間にわずかな隙間を作ります。

ディスプレイの亀裂がひどいと、吸盤が吸着しないことがあります。あらかじめディスプレイに梱包用テープを貼り付けておくと上手く行きやすいようです。または、吸盤をディスプレイに固く接着することも可能です。

開口ピックを隙間に差し込みます。

開口ピックをディスプレイの端と底部に沿ってスライドさせて、接着剤を剥がします。必要に応じてさらに加熱します。

ガラスは薄く、無理に力をかけると簡単に亀裂が入ってしまうため、慎重に作業を行ってください。

上端は最後に分離します。両側にアンテナがあるため、これらを損傷しないように注意してください。必要な場合は、無水エタノールを少量使用して、接着剤をほぐすことも可能です。

[* black] Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame.
[* icon_note] If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display.
[* black] Insert an opening pick into the gap.
[* black] Slide the pick around the sides and bottom of the display to cut the adhesive. Apply more heat as needed.
[* icon_caution] Work carefully—the glass is thin and will crack easily if you try to force it.
[* black] Separate the top edge last. There are antennas[link|https://d3nevzfk7ii3be.cloudfront.net/igi/yppINHAEbZMkdjiS.full|antennas on both sidessides|new_window=true], so be careful not to damage them. Use more heat or a bit of isopropyl alcohol to help weaken the adhesive.
[* black] Separate the top edge last. There are antennas[link|https://d3nevzfk7ii3be.cloudfront.net/igi/yppINHAEbZMkdjiS.full|antennas on both sidessides|new_window=true], so be careful not to damage them. Use more heat or a bit of isopropyl alcohol to help weaken the adhesive.

Your contributions are licensed under the open source Creative Commons license.