Skip to main content
English
Chinese

更换MacBook Pro 13'' Retina显示器2013末期版本的上部机身(C壳)

Guide Information

= Done = Incomplete
    Use this guide to replace the upper case.
    Use this guide to replace the upper case. This procedure involves using adhesive remover to remove the battery. '''Do not reuse the battery after it has been removed, as doing so is a potential safety hazard.''' Replace it with a new battery.
    '''iFixit adhesive remover is highly flammable.''' Perform this procedure in a well-ventilated area. Do not smoke or work near an open flame during this procedure.
    '''To minimize risk of damage, turn on your MacBook and allow the battery to fully discharge before starting this procedure.''' A charged lithium-ion battery can create a dangerous and uncontrollable fire if accidentally punctured. If your battery is swollen, [[What to do with a swollen battery|take extra precautions|new_window=true]].
    Some replacement upper case assemblies may include the trackpad and battery as well. In this case, skip steps 18 through 44.
    This guide requires the removal of the heat sink. Don't forget to follow our [guide|744|thermal paste application guide] before you reinstall your heat sink.

      Describe the specific part or component of this device you're working on. Ex: Battery

      Create a title.

      This brief summary will only appear in search results.

      Communicate background information before the reader dives into the guide.

      Guide Steps

      Step 1

      从散热铁边缘小心地移开风扇橡胶盖。

      Step 2

      用撬棒的平头把散热铁螺丝上的泡沫粘合剂剥掉。

      Step 3

      拆掉下列固定散热铁的螺丝:

      Step 4

      从笔记本上拿掉散热铁。

      Step 5

      用撬棒的尖头推iSight摄像头排线接头的两边,让它退出它在主板上的插槽。

      Step 6

      将iSight摄像头排线从风扇外壳上揭开,弯到一边。

      Step 7

      用撬棒的尖头翻起风扇ZIF接头的卡扣。

      Step 8

      拆掉下列将风扇固定在上部机身(C壳)上的螺丝:

      Step 9

      从散热铁凹槽那边抬起风扇,把它拉向笔记本合叶的方向来拿掉它。

      Step 10

      把撬棒的尖头插在每一根天线靠近接头处的下面,向上挑起来断开它们与网卡的连接。

      Step 11

      用撬棒的尖头推I/O板接头的两边,让它从它在主板上的插槽中退出。

      Step 12

      拆掉下列把I/O板固定在上部机身(C壳)上的螺丝:

      Step 13

      抬起I/O板边缘的I/O板排线,把它拉向主板方向来使端口脱离上部机身(C壳)。

      Step 14

      用撬棒的平头来断开键盘背光排线的连接并把它弯到一旁。

      Step 15

      如果有必要,揭开盖着麦克风排线ZIF接头的所有胶带。

      Step 16

      将麦克风排线直拉出它在主板上的插槽。

      Step 17

      如果有必要,揭开盖着键盘排线接头的所有胶带。

      Step 18

      将键盘排线直拉出它在主板上的ZIF插槽。

      Step 19

      拆掉这5颗将主板固定在上部机身(C壳)上的3.5mm T5 内梅花头螺丝。

      Step 20

      轻轻向上抬起主板的处理器那一端,将其拉向风扇方向来使端口与上部机身脱离,拿掉主板。

      Step 21

      用一把镊子摘掉显示器左右两边的合叶橡胶盖。

      Step 22

      拆掉将固定铝制合叶挡板固定在上部机身(C壳)上的3.2mm T5 内梅花头螺丝(两边都是)。

      Step 23

      用一把镊子把显示器左右合叶的铝制挡板夹走。

      Step 24

      拆掉内侧的这4颗将显示器固定在上部机身(C壳)上的5.3mm T8 内梅花头螺丝(每边两个)。

      Step 25

      以一个略大于90度的角度打开Macbook Pro,侧面朝下放着它,如图。

      Step 26

      握紧两片设备,一手一个。

      Step 27

      把MacBook放在一个加过热的iOpener上几分钟来使固定双麦克风排线的胶变软。

      Step 28

      把撬棒的尖头插到麦克风排线的橡胶盖以下来将其从上部机身(C壳)上分离。

      Step 29

      把撬棒的尖头插到麦克风排线的接头处以下,把这块区域向上挑离上部机身(C壳)。

      Step 30

      把撬棒的尖头插到麦克风排线右边位置以下,并滑向螺丝处来将其从上部机身(C壳)分离。

      Step 31

      将麦克风排线从上部机身(C壳)上拿掉。

      Your contributions are licensed under the open source Creative Commons license.