Skip to main content

Notice: You are editing a prerequisite guide. Any changes you make will affect all 4 guides that include this step.

English
German

Translating step 9

Step 9
To reinstall the back cover:
  • To reinstall the back cover:

  • Use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.

  • Clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as Tesa 61395. Be aware that this leaves gaps that are vulnerable to liquid intrusion.

  • After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

So wird die Rückabdeckung wieder eingebaut:

Löse zunächst mit einer Pinzette alle Kleberreste von der Rückabdeckung und vom Rahmen des Smartphones ab.

Reinige dann die Klebeflächen mit hochkonzentrierte Isopropylakohol (mindestens 90%) und einem fusselfreien Tuch. Wische nur in eine Richtung, nicht vor und zurück. Dadurch werden die Flächen für den neuen Kleber vorbereitet.

Schalte dein Smartphone ein und prüfe, ob deine Reparatur gelungen ist, bevor du neuen Kleber anbringst und das Gerät wieder zuklebst.

Ersatzklebeband gibt es in vorgestanzter Form, so dass es genau auf die Konturen der Rückabdeckung passt. Wenn du das nicht hast, kannst du auch extra starkes doppelseitiges Klebeband, wie Tesa 61395 benutzen. Sei dir aber im Klaren darüber, dass dabei Lücken entstehen, durch die Feuchtigkeit eindringen kann.

Übe nach dem Einbau der Rückabdeckung mehrere Minuten lang starken und konstanten Druck auf das Smartphone aus, damit sich der Kleber gut verbinden kann. Du kannst das Smartphone dazu zum Beispiel unter einen Stapel Bücher legen.

Wenn du willst, kannst du die Rückabdeckung auch ohne neuen Kleber anbringen. Beseitige zunächst alle größeren Klebstoffklumpen, die verhindern könnten, dass die Rückabdeckung plan aufliegt. Wenn sie richtig sitzt, dann erwärme sie und presse sie gut fest. Sie ist dann zwar nicht mehr wasserfest, aber normalerweise ist der Kleber stark genug.

[* icon_reminder] To reinstall the back cover:
- [* black] First use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.
- [* black] Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
+ [* black] Use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.
+ [* black] Clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
[* black] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
[* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

Your contributions are licensed under the open source Creative Commons license.