Introduction

The guide takes place from the Camera Lens Assembly guide.

Parts

No parts required.

Locate the memory card and battery card latch on the bottom of the camera.
  • Locate the memory card and battery card latch on the bottom of the camera.

  • Slide the latch to the open position.

Add Comment

Open the battery latch, and slide the battery release lever to the right.
  • Open the battery latch, and slide the battery release lever to the right.

Add Comment

Remove the battery from the camera.
  • Remove the battery from the camera.

Add Comment

Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.
  • Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

  • Use this screwdriver for all screws in the device.

Add Comment

Remove the 3.15 mm screw on the left side of the camera.
  • Remove the 3.15 mm screw on the left side of the camera.

Add Comment

Remove the left side casing. Remove the left side casing.
  • Remove the left side casing.

Add Comment

Remove the two 3.15 mm screws on the right side of the camera.
  • Remove the two 3.15 mm screws on the right side of the camera.

Add Comment

Remove the bottom right panel.
  • Remove the bottom right panel.

Add Comment

Gently remove the back casing. Start at the bottom and carefully pry towards the top to get this piece free.
  • Gently remove the back casing.

  • Start at the bottom and carefully pry towards the top to get this piece free.

Add Comment

Remove the two black 5.35 mm screws that hold in the front faceplate. There may be a third screw the the right of the lens assembly.
  • Remove the two black 5.35 mm screws that hold in the front faceplate.

  • There may be a third screw the the right of the lens assembly.

Add Comment

Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery.
  • Carefully remove the upper assembly, which houses the buttons and the flash battery.

Add Comment

Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.
  • Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

Add Comment

Remove the three black 5mm screws attached to the lens frame. Remove the three black 5mm screws attached to the lens frame.
  • Remove the three black 5mm screws attached to the lens frame.

Add Comment

Remove the lens frame.
  • Remove the lens frame.

Add Comment

Lift out the circuit board as shown.
  • Lift out the circuit board as shown.

Add Comment

Lift the two black latches that hold the connector ribbons in place. Disconnect the two ribbons.
  • Lift the two black latches that hold the connector ribbons in place.

  • Disconnect the two ribbons.

Add Comment

Remove the lens assembly as shown.
  • Remove the lens assembly as shown.

Add Comment

Remove four 4mm screws from the lens assembly.
  • Remove four 4mm screws from the lens assembly.

Add Comment

Carefully turn over the assembly. Carefully turn over the assembly.
  • Carefully turn over the assembly.

Add Comment

Remove the Fixed Frame Unit by separating it from the assembly. Remove the Direct Frame Unit from the assembly.
  • Remove the Fixed Frame Unit by separating it from the assembly.

  • Remove the Direct Frame Unit from the assembly.

Add Comment

Remove the 1st lens frame from the lens assembly.
  • Remove the 1st lens frame from the lens assembly.

Add Comment

Detach the 2nd Frame Unit from the assembly.
  • Detach the 2nd Frame Unit from the assembly.

Add Comment

Remove the 4mm screw from the lens housing.
  • Remove the 4mm screw from the lens housing.

Add Comment

Separate the lens housing.
  • Separate the lens housing.

  • Replace the lens by gently prying away from the assembly.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 other people completed this guide.

Caleb Fink

Member since: 10/11/2010

186 Reputation

2 Guides authored

Team

Cal Poly, Team 9-22, Regan Fall 2010 Member of Cal Poly, Team 9-22, Regan Fall 2010

CPSU-REGAN-F10S9G22

4 Members

8 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 4

Past 30 Days: 35

All Time: 11,660