Fix Your Stuff Community Store

You're viewing a previously published version of this guide.  View latest version

Older
Jun 19, 2018 - 09:06:26
Jun 19, 2018 - 09:06:26 Jun 19, 2018 - 09:06:26 Jun 19, 2018 - 09:06:25 Jun 19, 2018 - 09:06:04 Jun 19, 2018 - 09:06:54 Jun 19, 2018 - 09:06:32 Jun 07, 2018 - 10:06:34 May 31, 2018 - 10:05:25 May 31, 2018 - 10:05:35 May 31, 2018 - 10:05:38 May 29, 2018 - 10:05:50 May 29, 2018 - 10:05:31 May 29, 2018 - 10:05:49 May 29, 2018 - 10:05:17 May 19, 2018 - 12:05:17 May 19, 2018 - 12:05:15 May 19, 2018 - 11:05:02 May 17, 2018 - 10:05:27 May 17, 2018 - 10:05:48 May 17, 2018 - 10:05:56 May 17, 2018 - 10:05:13 May 17, 2018 - 10:05:50 May 17, 2018 - 10:05:57 May 17, 2018 - 10:05:27 May 17, 2018 - 10:05:53 May 17, 2018 - 10:05:52 May 17, 2018 - 10:05:29 May 17, 2018 - 10:05:49 May 17, 2018 - 10:05:27 May 17, 2018 - 10:05:14 May 17, 2018 - 10:05:37 May 17, 2018 - 10:05:19 May 17, 2018 - 10:05:48 May 17, 2018 - 10:05:51 May 17, 2018 - 10:05:18 May 17, 2018 - 10:05:26 May 12, 2018 - 12:05:13 May 12, 2018 - 12:05:47 May 12, 2018 - 12:05:10 May 12, 2018 - 12:05:33 May 12, 2018 - 12:05:20 May 12, 2018 - 12:05:27
Newer

Wolf Gourmet WGBL100S Blades Replacement

Written By: Luke Kutz (and 5 other contributors)
  • Comments: 1
  • Favorites: 0

Difficulty

Moderate

Steps

5

Time Required

10 - 15 minutes

Sections

1

Flags

1

Featured Student Guide

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

Introduction

If your blender is not chopping food correctly, consider replacing the blades. The blades can be very sharp, so please take caution when proceeding with this guide.

  1. Flip over the pitcher to expose the base of the blade assembly.

    • Flip over the pitcher to expose the base of the blade assembly.

    • Using the H4.0 Allen key from the 54 bit driver kit, attached to an impact driver, remove the socket head cap screw from the drive coupling.

    • Apply a solvent to remove adhesive if necessary.

  2. Using a pair of pliers, pull of the drive shaft coupling.

    • Using a pair of pliers, pull of the drive shaft coupling.

  4. Using a flat head screwdriver and a mallet, bend down the two tabs holding the large nut. Using a flat head screwdriver and a mallet, bend down the two tabs holding the large nut.

    • Using a flat head screwdriver and a mallet, bend down the two tabs holding the large nut.

  5. Remove the nut using a crescent wrench.

    • Remove the nut using a crescent wrench.

  6. Push the blade assembly into the jar.

    • Push the blade assembly into the jar.

    • Remove the blades from the device.

    • Be careful not to cut yourself when handling the blades.

Author

with 5 other contributors

Luke Kutz

Member since: 04/19/2018

345 Reputation

3 Guides authored

Badges: 7

+4 more badges

Team

Cal Poly, Team S25-G16, Maness Spring 2018 Member of Cal Poly, Team S25-G16, Maness Spring 2018

CPSU-MANESS-S18S25G16

4 Members

5 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 7

All Time: 478