Introduction

This guide provides instruction for installing a ribbon containing a speaker, GPS and camera for the Sony Ericsson TM506 cell phone.

Image 1/3: Push down with your thumb until the battery cover comes off. Image 2/3: Push down with your thumb until the battery cover comes off. Image 3/3: Push down with your thumb until the battery cover comes off.
  • Firmly hold the phone between your fingers with your thumb on the battery cover.

  • Push down with your thumb until the battery cover comes off.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Unscrew the bottom two 5.4mm screws with a Torx T6 screwdriver.

Add Comment

Image 1/2: Image 2/2:
  • Remove the two rubber casings for the top two screws with a plastic opening tool.

Add Comment

Image 1/1:
  • Unscrew these two 5.4mm screws with a Torx T6 screwdriver.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • There are eight snap hooks located around the outer case. Carefully snap these to remove the outer case.

Add Comment

Image 1/3: Lift the sound box up to remove it from the case. Image 2/3: Lift the sound box up to remove it from the case. Image 3/3: Lift the sound box up to remove it from the case.
  • The sound box is attached to the case by two snap hooks.

  • Lift the sound box up to remove it from the case.

Add Comment

Image 1/2: Carefully, lift up on the connector to separate it from the board. Image 2/2: Carefully, lift up on the connector to separate it from the board.
  • Locate the 80-pin connector.

  • Carefully, lift up on the connector to separate it from the board.

Add Comment

Image 1/3: Using a plastic opening tool, carefully lift up on the motherboard to detach it. Image 2/3: The motherboard is extremely fragile. Try to be forceful yet delicate in the removal because it will not come off easily. Image 3/3: The motherboard is extremely fragile. Try to be forceful yet delicate in the removal because it will not come off easily.
  • There are two snap hooks that attach the motherboard to the case.

  • Using a plastic opening tool, carefully lift up on the motherboard to detach it.

  • The motherboard is extremely fragile. Try to be forceful yet delicate in the removal because it will not come off easily.

Add Comment

Image 1/2: The hinge stopper should be about 5.5mm in. Image 2/2: The hinge stopper should be about 5.5mm in.
  • Use tweezers to push the hinge stopper in until it can no longer be moved.

  • The hinge stopper should be about 5.5mm in.

Add Comment

Image 1/2: Don't completely pull apart the two pieces or you will damage the ribbon. Image 2/2: Don't completely pull apart the two pieces or you will damage the ribbon.
  • Separate the bottom and top half of the phone from the hinge they are connected by.

  • Don't completely pull apart the two pieces or you will damage the ribbon.

Add Comment

Image 1/1:
  • Pull the ribbon through the opening in the hinge to completely separate the upper and lower halves of the phone.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • The top and bottom covers are held in place by adhesive. To remove them, use a pushpin in the four indentations indicated to remove.

Add Comment

Image 1/2: Image 2/2:
  • Remove the four 5.4 mm screws with a Torx T5 screwdriver.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Use a plastic opening tool in the indicated location and apply pressure until the case hook is detached. Then lift the case up until the two pieces are detached.

Add Comment

Image 1/3: Detach the GPS from the case by carefully lifting it up from the case. Image 2/3: Detach the camera with your hands or by using a paperclip similar to the way the speaker was removed. Image 3/3: Detach the camera with your hands or by using a paperclip similar to the way the speaker was removed.
  • Use a paperclip to detach the speaker from the case.

  • Detach the GPS from the case by carefully lifting it up from the case.

  • Detach the camera with your hands or by using a paperclip similar to the way the speaker was removed.

Add Comment

Image 1/2: Simply, move the ribbon to the right and it will be completely detached from the case. Image 2/2: Simply, move the ribbon to the right and it will be completely detached from the case.
  • Once the three components are detached, removing the ribbon is possible.

  • Simply, move the ribbon to the right and it will be completely detached from the case.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Daniel

Member since: 06/20/2012

71 Reputation

7 Guides authored

Team

Cal Poly, Team 1-1, Regan SU 2012 Member of Cal Poly, Team 1-1, Regan SU 2012

CPSU-REGAN-SU12S1G1

2 Members

8 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 0

All Time: 1,095