Introduction

This guide provides access to the LCD of the camera, which is necessary to remove for many other parts. Replacing the LCD is a common procedure for this camera.

The battery cover is located on the right side of the camera.
  • The battery cover is located on the right side of the camera.

  • Slide the cover to expose the battery.

Add Comment

Ensure that the battery lines up properly with the slot in the camera.
  • Ensure that the battery lines up properly with the slot in the camera.

  • Slide battery in.

  • Slide cover closed.

  • Battery not shown

Add Comment

Remove screws from outside of camera. There are 6 screws total. 3 screws on underside. 1 screw on right side, near battery cover.
  • Remove screws from outside of camera. There are 6 screws total.

  • 3 screws on underside.

  • 1 screw on right side, near battery cover.

  • 2 screws on left side.

Add Comment

Use screwdriver to remove screws.
  • Use screwdriver to remove screws.

Add Comment

Gently pull the front cover off of the main camera.
  • Gently pull the front cover off of the main camera.

  • All of the inner parts of the camera are attached to the back screen.

Add Comment

The front cover is now removed from the camera and the internal hardware is now exposed.
  • The front cover is now removed from the camera and the internal hardware is now exposed.

Add Comment

This is the camera without the front cover.
  • This is the camera without the front cover.

Add Comment

Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.
  • Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.

Add Comment

Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are. Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are. Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.
  • Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.

Add Comment

Pull apart the inner hardware from the back case by prying on the left side. Pull apart the inner hardware from the back case by prying on the left side. Pull apart the inner hardware from the back case by prying on the left side.
  • Pull apart the inner hardware from the back case by prying on the left side.

Add Comment

Remove the back cover.
  • Remove the back cover.

Add Comment

The back cover is now removed from the internal hardware.
  • The back cover is now removed from the internal hardware.

Add Comment

Use the spudger to pry the LCD from the camera.
  • Use the spudger to pry the LCD from the camera.

Add Comment

The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.
  • The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.

Add Comment

Flip camera to other side. Use tweezers to peel off black sticker, located in middle of the motherboard.
  • Flip camera to other side.

  • Use tweezers to peel off black sticker, located in middle of the motherboard.

Add Comment

Use pry stick to pop out LCD connector ribbon, also called the ZIF connector. Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.
  • Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.

Add Comment

The LCD is now removed from the camera.
  • The LCD is now removed from the camera.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Stephannie Allen

Member since: 03/11/2013

165 Reputation

10 Guides authored

Team

Clemson, Team 13-1, Benson Spring 2013 Member of Clemson, Team 13-1, Benson Spring 2013

CLEM-BENSON-S13S13G1

4 Members

10 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 10

All Time: 558