You're viewing a previously published version of this guide. View latest version

Jul 20, 2017 - 09:07:33

Jul 20, 2017 - 09:07:33 Jul 18, 2017 - 09:07:26 Jul 18, 2017 - 08:07:07 Jul 18, 2017 - 08:07:06 Jul 18, 2017 - 08:07:07 Jul 17, 2017 - 02:07:57 Jan 28, 2014 - 02:01:09 Sep 04, 2013 - 05:09:01 Jul 31, 2013 - 05:07:55 May 28, 2013 - 02:05:01 May 28, 2013 - 02:05:41 May 28, 2013 - 02:05:36 Mar 21, 2011 - 06:03:12 Mar 21, 2011 - 06:03:58 Mar 21, 2011 - 06:03:16 Mar 11, 2011 - 12:03:43 Mar 11, 2011 - 12:03:32 Mar 11, 2011 - 12:03:38 Mar 11, 2011 - 12:03:28 Mar 11, 2011 - 12:03:56 Mar 11, 2011 - 12:03:45 Mar 11, 2011 - 12:03:12 Mar 10, 2011 - 05:03:51 Mar 09, 2011 - 04:03:49 Mar 09, 2011 - 04:03:08 Mar 02, 2011 - 04:03:45 Mar 02, 2011 - 03:03:30 Mar 02, 2011 - 03:03:26 Mar 02, 2011 - 03:03:30 Mar 02, 2011 - 03:03:27 Mar 02, 2011 - 03:03:29 Mar 02, 2011 - 02:03:39 Mar 02, 2011 - 02:03:00 Mar 02, 2011 - 02:03:29 Mar 01, 2011 - 06:03:25 Mar 01, 2011 - 06:03:23 Mar 01, 2011 - 06:03:54 Mar 01, 2011 - 06:03:52 Mar 01, 2011 - 06:03:36 Mar 01, 2011 - 06:03:35 Mar 01, 2011 - 06:03:17 Mar 01, 2011 - 06:03:15 Mar 01, 2011 - 05:03:12

Newer

Sony Cyber-shot DSC-P52 Outer Case Replacement

Written By: Trevor (and 6 other contributors)

Comments: 0
Favorites: 1

Sony Cyber-shot DSC-P52 Outer Case Replacement

Difficulty

Moderate

Steps

Time Required

2 - 10 minutes

Introduction

This guide is used for taking apart the case to fix many of the issues of the Sony Cybershot DSC-P52.

Tools

Buy these tools

Phillips #0 Screwdriver

$5.49

Buy

Parts

No parts specified.

Step 1 Outer Case

Open the battery compartment and remove the batteries.

Open the battery compartment and remove the batteries.
Remove all of the visible screws on the outside of the case.
There should be three of them that are all easily located.

Step 2

Open the memory card compartment.
Remove the screw next to the memory card slot.

Step 3

Pull apart the front and back cover pieces carefully.

Pull apart the front and back cover pieces carefully.
The front cover should come completely free with little effort.
The back cover will still be attached to the circuit board.

Step 4

Simultaneously unclip all of the clips holding in the circuitry. Remove the back case.

Simultaneously unclip all of the clips holding in the circuitry. Remove the back case.
The circuitry will still be connected to the back case by ribbon cables.