Introduction

Before beginning this guide, ensure that the device is both unplugged and cool; failure to do so may result in electrocution or burns.

Parts

No parts required.

Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron. Remove the back cover piece. Make sure the iron is unplugged and cooled off.
  • Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron.

  • Remove the back cover piece.

  • Make sure the iron is unplugged and cooled off.

Add Comment

Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron. Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.
  • Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron.

  • Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.

  • Removing the left black wire will also free the red wire, attached by the same screw.

Add Comment

Pull the split end of the power cord upward through the ball joint.
  • Pull the split end of the power cord upward through the ball joint.

  • Set aside the power cord.

Add Comment

Use the Philips head #0 screwdriver to remove the remaining 6.58mm screws that hold the wires on the bottom (brown and blue). Remove from left to right Unclip the black adapter piece on the bottom right.
  • Use the Philips head #0 screwdriver to remove the remaining 6.58mm screws that hold the wires on the bottom (brown and blue).

  • Remove from left to right

  • Unclip the black adapter piece on the bottom right.

  • Wires order (from left to right): Brown, Blue, Red, Black

Add Comment

Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board. Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board.
  • Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board.

Add Comment

Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board. Gently pull the circuit board from affixed position.
  • Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board.

  • Gently pull the circuit board from affixed position.

  • The circuit board will not be completely separated at this point.

Add Comment

Remove the mode display piece and set aside. Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle. Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.
  • Remove the mode display piece and set aside.

  • Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.

Add Comment

Remove the connecting wire from the connected adapter in the handle by pulling lightly.
  • Remove the connecting wire from the connected adapter in the handle by pulling lightly.

  • Set aside the circuit board.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Drew Carff

Member since: 10/23/2017

540 Reputation

5 Guides authored

Team

USF Tampa, Team S1-G4, Leahy Fall 2017 Member of USF Tampa, Team S1-G4, Leahy Fall 2017

USFT-LEAHY-F17S1G4

3 Members

5 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 10

Past 30 Days: 25

All Time: 184