Fix Your Stuff Community Store

Ozeri Pronto ZK14-S LCD Replacement

Introduction

This guide explains how to expose the LCD screen of the Ozeri Pronto ZK14-S. The detachment of the LCD motherboard is necessary to reveal the actual screen.

What you need

  1. Ozeri Pronto ZK14-S LCD Replacement, Panel Removal: step 1, image 1 of 2 Ozeri Pronto ZK14-S LCD Replacement, Panel Removal: step 1, image 2 of 2

    • Twist the plastic plate slowly to the left to pull it away.

    Edit

  2. Ozeri Pronto ZK14-S LCD Replacement: step 2, image 1 of 1

    • Lift up the sticker at the bottom where the “Ozeri” logo is to reveal a screw.

    • The sticker does not need to be completely removed.

    Edit

  3. Ozeri Pronto ZK14-S LCD Replacement: step 3, image 1 of 1

    • Using a 2.0 Flathead screwdriver, remove the 9.50 mm Phillips head screw under the sticker.

    Edit

  4. Ozeri Pronto ZK14-S LCD Replacement: step 4, image 1 of 2 Ozeri Pronto ZK14-S LCD Replacement: step 4, image 2 of 2

    • Using a 2.0 Flathead screwdriver, remove the two 18.76 mm Phillips head screws in the plate stand.

    Edit

  6. Ozeri Pronto ZK14-S LCD Replacement: step 5, image 1 of 2 Ozeri Pronto ZK14-S LCD Replacement: step 5, image 2 of 2

    • Using a 2.0 Flathead screwdriver, remove the 9.44 mm Phillips head screw on the edge opposite to the LCD screen.

    Edit

  7. Ozeri Pronto ZK14-S LCD Replacement: step 6, image 1 of 1

    • Turn the device over so the back panel is facing up.

    Edit

  8. Ozeri Pronto ZK14-S LCD Replacement: step 7, image 1 of 1

    • Using the iFixit opening tool, pry off the two rubber stubs on the right side and the two rubber stubs on the left side of the bottom of the device.

    Edit

  9. Ozeri Pronto ZK14-S LCD Replacement: step 8, image 1 of 1

    • Using a 2.0 Flathead screwdriver, remove the four 9.46 mm Phillips head screws that were under the rubber stubs.

    Edit

  10. Ozeri Pronto ZK14-S LCD Replacement: step 9, image 1 of 2 Ozeri Pronto ZK14-S LCD Replacement: step 9, image 2 of 2

    • Pry apart the two panels to separate them from each other.

    • Flip the device over so the LCD is facing up. Flip the front panel over on its side.

    • Be careful when separating the panels to avoid damaging the wires they are connected by.

    Edit

  11. Ozeri Pronto ZK14-S LCD Replacement, LCD: step 10, image 1 of 2 Ozeri Pronto ZK14-S LCD Replacement, LCD: step 10, image 2 of 2
    Tool used on this step:
    Flathead 3/32" or 2.5 mm Screwdriver
    $5.49
    Buy

    • Using the 2.0 Flathead screwdriver, remove the three 7.20 mm screw on the back of the center LCD motherboard.

    Edit

  12. Ozeri Pronto ZK14-S LCD Replacement: step 11, image 1 of 3 Ozeri Pronto ZK14-S LCD Replacement: step 11, image 2 of 3 Ozeri Pronto ZK14-S LCD Replacement: step 11, image 3 of 3

    • Stand the center motherboard up to expose the LCD screen

    • Be careful when standing up the LCD motherboard to avoid damaging the wires it is connected to.

    • Remove the LCD screen.

    Edit
Conclusion

To reassemble your device, follow these instructions in reverse order.

3 other people completed this guide.

Author

with 2 other contributors

Oneika White

Member since: 10/01/15

709 Reputation

4 Guides authored

Badges: 15

+12 more badges

Team

USF Tampa, Team 1-4, Leahy Fall 2015 Member of USF Tampa, Team 1-4, Leahy Fall 2015

USFT-LEAHY-F15S1G4

4 Members

5 Guides authored

One Comment

I had a similar model, it was different to open but the LCD was showing all 8's, I just reset the same LCD and it worked like new.

Dennis Lima - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 3

All Time: 546