Introduction

Using this guide, people will be able to replace the plastic shell of their blender in case of cracks or aesthetic issues.

Remove the cup from the blender base.
  • Remove the cup from the blender base.

Add Comment

Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units. Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units.
  • Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units.

The three screws holding the slotted base in place on some units are Torx Security bits (TR9) not phillips. The tool is listed above (T9 Torx Screwdriver is actually a TR9 Torx Security Screwdriver . It’s the right tool.

Dennis Carr - Reply

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Using a the standard Phillips head screwdriver bit, remove the slotted black plastic covering and then unscrew the one 11mm screw holding the power cord in place. Unscrew the four 14 mm screws that are in the deep slots.  This will release the motor from the base. Unscrew the four 14 mm screws that are in the deep slots.  This will release the motor from the base.
  • Using a the standard Phillips head screwdriver bit, remove the slotted black plastic covering and then unscrew the one 11mm screw holding the power cord in place.

  • Unscrew the four 14 mm screws that are in the deep slots. This will release the motor from the base.

Add Comment

CAUTION: the silver blade attached to the motor is very sharp.  Use a towel or thick cloth to protect your hands for the next step. Using a towel, hold the silver fan still.  Twist the small black rubber wheel that is attached to the top of the blender base to the right.  This will remove the wheel for replacement. Using a towel, hold the silver fan still.  Twist the small black rubber wheel that is attached to the top of the blender base to the right.  This will remove the wheel for replacement.
  • CAUTION: the silver blade attached to the motor is very sharp. Use a towel or thick cloth to protect your hands for the next step.

  • Using a towel, hold the silver fan still. Twist the small black rubber wheel that is attached to the top of the blender base to the right. This will remove the wheel for replacement.

Add Comment

Use the standard Phillips head screw bit to unscrew the screws in the black plastic with the silver circular discs. Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor. Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor.
  • Use the standard Phillips head screw bit to unscrew the screws in the black plastic with the silver circular discs.

  • Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor.

Add Comment

Untwist the small rubber connector to detach the plastic from the motor. Untwist the small rubber connector to detach the plastic from the motor.
  • Untwist the small rubber connector to detach the plastic from the motor.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Morgan Blauth

Member since: 02/24/2016

692 Reputation

5 Guides authored

Team

USF Tampa, Team 1-5, Leahy Spring 2016 Member of USF Tampa, Team 1-5, Leahy Spring 2016

USFT-LEAHY-S16S1G5

2 Members

5 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 3

Past 7 Days: 12

Past 30 Days: 42

All Time: 587